Jump to content
SAU Community

Recommended Posts

so 99% sure my bottom end bearings went on my 25

ive got the motor out now when i take the oil pan off

what should i be looking for?

any info would help cheers.

is there anyone that can help? or should this be moved to where

it would get more attention?

so i have taken the sump off and havnt noticed anything.

motor still cranks over and there are no flakes of metal anywhere

to be found. i have another motor to put in so should just sell this as is or

pull it apart and find this mystery problem?

ok here are some picks does this help?

also was looking at my valves on the exh side

when i took the manifold off i could see up there.

there was white carbon dust on them but

my other motor only has black carbon?

any feedback would help.

post-69261-1281422419_thumb.jpgpost-69261-1281422431_thumb.jpg[attachmen

t=299739:bottomend_2.jpg]

post-69261-1281422444_thumb.jpg

You'll need to pull the big end/main caps off to see what the condition of the bearings is. If you do that and post up photos of the bearings then lots of people on here would have experience in engine rebuilds and will tell you whats been happening

As already said but, major damage will be pretty obvious.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...