Jump to content
SAU Community

Recommended Posts

  • Replies 381
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i remember my thought proces quite well:

"okay here we go, 50 meter board, wait, wait, wait BBBBRRRRAAAAAAKKKKEEEEE, turn in......

shit, too much

catch it... hey check out this cool slide.... ah wel its gone too far, keep the power on and do a big skidOOOOHHHHHH SSSHHHHHIIIIIIIITTTTTT!!!!!!!!"

then a little bit of wee came out

what lsd you got in the mx5? can't be the standard viscous?

i went with a mechanical because for the price id much rather a brand new item. Second hand torsens still got for 8-900 bucks, where as i got my cusco for $1200. That and i want to keep taking mine to the track so i nice fresh meachanical lsd should make quite a big improvement....

;)"looks at josh"

:(

Well the speedo is not connected, and I over estimated. just calculated my speed from my tach, only hit 180Km/h.

6500 rpm 235/45R17 (643mm dia) 4.36 diff in 4th 1.1

didn't mean to BS, but it was very hairy having the ass step right out on you at that speed any way

Interesting to compare setups, going by the calculator that was linked in this thread (Which must be in miles an hour not kilometers) I was doing roughly 185 through the kink and the car was dead stable at full noise in fourth (Where I could touch my conservative limiter before the hairpin) or in fifth gear. I have roughly 180-190 rwkw so I am happy enough with that for the first time I ever saw the track. The stability I reckon is the difference in our setups. my spring rates are about 8 / 5.6 and while it needed more roll stiffness, it had good traction out of most corners with an LSD that does not work (Budget) but it understeered a bit more than I liked in the slow stuff. on the plus side it just rode through the turn one bump like it was not there, flat in third gear at about 6000 RPM and it did not even change line. Biggest thing I would need to be at Mallala would be to be a lot more agressive under brakes, I was being pretty conservative on them to preserve the car, the pedal never even softened.

I should push the car a lot harder as I was only doing 25's or so on the laps I ran it up a bit, but I had a Hillclimb one week later back in Vic when I would only get home mid week so bending or breaking the car was just not on the screen for me at a day that I just wanted to have fun. I would have been out of the hillclimb if I broke ANYTHING on the car, as would the other bloke who usualy drives the car with me.

just to add my 2c to the speedo, my ecu reports 194-198km/h top speed on the kink, depending on how well I exit the southern hairpin and how late I brake.

Haven't yet cracked the 200, interesting that the R35 hits about the same, but given I'm doing 1:21's not 1:12's I'm guessing the R35 kisses 200 before the kink rather than at terminal velocity into the northern hairpin?

For sake of comparing apples and oranges, the car is a BNR32 with 285kw on A048 semis.

just to add my 2c to the speedo, my ecu reports 194-198km/h top speed on the kink, depending on how well I exit the southern hairpin and how late I brake.

Haven't yet cracked the 200, interesting that the R35 hits about the same, but given I'm doing 1:21's not 1:12's I'm guessing the R35 kisses 200 before the kink rather than at terminal velocity into the northern hairpin?

For sake of comparing apples and oranges, the car is a BNR32 with 285kw on A048 semis.

How are you getting ECU speed read outs? PFC?

Just as a point of interest. Our ECU logging at the Apex point of the Kink - not 100m before it - not 100m after it - will normally indicate around 228 - 232kmh. Actual GPS logged speed from the VBox is closer to 205 - 208km/h. A genuine 200km/h at the apex of the Kink needs three things - 1) A bloody powerful car to accelerate you to that true speed. 2) A very, very good chassis and normally slicks to take the side load generated (we generate around 1.4G lateral constant in the R35 at that point). 3) An even bigger set of balls as you need to clip the kerb on the outside of the track at that speed to make it all work :(

To put that in context our EVO X which just recorded 5th fastest outright 400m time at Tailem Bend sprints with an 11.9 second quarter pass touches an actual 185km/h on a flyer at the apex when on a 1:15.X lap. While huge amounts of Disney Dyno jiggerwatts help, the main thing that determines your speed at this point of the track is your exit from Turn 3, which must be flat from the apex onwards.

Also if you lift of the throttle - at all - for the Kink, you are doing it wrong. Its a bend that must be taken flat if you want a lap time....

As they say you need to drive 'Flat Out" :)

Just as a point of interest. Our ECU logging at the Apex point of the Kink - not 100m before it - not 100m after it - will normally indicate around 228 - 232kmh. Actual GPS logged speed from the VBox is closer to 205 - 208km/h. A genuine 200km/h at the apex of the Kink needs three things - 1) A bloody powerful car to accelerate you to that true speed. 2) A very, very good chassis and normally slicks to take the side load generated (we generate around 1.4G lateral constant in the R35 at that point). 3) An even bigger set of balls as you need to clip the kerb on the outside of the track at that speed to make it all work :(

To put that in context our EVO X which just recorded 5th fastest outright 400m time at Tailem Bend sprints with an 11.9 second quarter pass touches an actual 185km/h on a flyer at the apex when on a 1:15.X lap. While huge amounts of Disney Dyno jiggerwatts help, the main thing that determines your speed at this point of the track is your exit from Turn 3, which must be flat from the apex onwards.

Also if you lift of the throttle - at all - for the Kink, you are doing it wrong. Its a bend that must be taken flat if you want a lap time....

As they say you need to drive 'Flat Out" :)

What would account for the speed difference in what the ECU reports compared to GPS? Not wheelspin I would presume in a GTR even with big power?

I will have to have a look over my video footage again, I might have had only the first shift light stage on in the kink when I was running it flat in fourth, that is set at 6000 rpm with the second stage at 6500, if I was part way between the two that would be about 170KMH. Most laps to be nice on the car for the following weekend I slotted it into top gear before the kink and ran to the hairpin in that, would not have cost me much into the kink but it certainly cost me at the end of the straight.

how do you rate the A048's andrew???

pretty good but they're the only semis I've had on the GTR. I had RE55s on the S15 which I felt were much grippier, but the S15 is 200kg lighter and RWD so difficult to compare directly. If I had a choice I'd go RE55s next, but need to get a spare set of rims first as the RE55s aren't DOT approved. A048s are $100/corner cheaper though.

How are you getting ECU speed read outs? PFC?

I'm running a nistune and have the ecutalk LCD running off the consult port. For anyone running a nissan ecu I reckon it is a great little unit - max-value storage and over-limit alarming for most parameters like injector %, water temp, rpm, AFM Voltage etc. The guy who makes them is working on in-built data logging to the microSD card, currently you need to plug a laptop into the USB port for logging. For the price I think they are excellent trackday diagnostic tool, but there's a few things it doesn't have that would be good - boost, oil temp & oil pressure (not available from the Nissan ECU) and intake air temp (in the ECU for GTR but not used by ecutalk)

Max vals from one of the Skynats sessions:

post-63364-1285760003_thumb.jpg

Just as a point of interest. Our ECU logging at the Apex point of the Kink - not 100m before it - not 100m after it - will normally indicate around 228 - 232kmh.

Well that makes more sense! and man that is fast! Maybe rolling diameter might be some of the difference between GPS and ECU indicated speeds?

thanks for the comps guys :) I must say after switching from the S15 I am loving my GTR too! ;)

What would account for the speed difference in what the ECU reports compared to GPS? Not wheelspin I would presume in a GTR even with big power?

Normally the basics of instrument inaccuracy (accounts for about 15km/h of it I reckon) plus the issues of tyre growth and distortion account for the error ;)

Notably the 'Kink' is the place that makes or breaks your lap. You can make seconds up (or lose them) right there

pretty good but they're the only semis I've had on the GTR. I had RE55s on the S15 which I felt were much grippier, but the S15 is 200kg lighter and RWD so difficult to compare directly. If I had a choice I'd go RE55s next, but need to get a spare set of rims first as the RE55s aren't DOT approved. A048s are $100/corner cheaper though.

thanks for that Andrew....i am prob going to be looking at a set sometime soon...the AO48's seem a lot cheaper then the RE55S...thats after i trial my set of KU36's

thanks for that Andrew....i am prob going to be looking at a set sometime soon...the AO48's seem a lot cheaper then the RE55S...thats after i trial my set of KU36's

Another tyre to have a look at would be the Toyo R888. That is what we have settled on for my coupe.

The Dunlop 01G was another we tried, I am sure they are a little faster overall than the Toyo, but it is more expensive, took longer to warm up and work, had less feel and was just not as nice in the rain as the Toyo. All things that worked against it for Hillclimbs on a typically damp and cold track! Even at Phillip Island the confidence you could have to just stick it in there on out laps at the 6 hour regularity was just not there compared to the Toyo. The Toyo started to feel good about halfway into the first corner.

Another tyre to have a look at would be the Toyo R888. That is what we have settled on for my coupe.

The Dunlop 01G was another we tried, I am sure they are a little faster overall than the Toyo, but it is more expensive, took longer to warm up and work, had less feel and was just not as nice in the rain as the Toyo. All things that worked against it for Hillclimbs on a typically damp and cold track! Even at Phillip Island the confidence you could have to just stick it in there on out laps at the 6 hour regularity was just not there compared to the Toyo. The Toyo started to feel good about halfway into the first corner.

Yeah what i have heard about the toyos is that they are softer, so good for light cars, out laps or short motorkhanas and hill climbs, but go off quickly after multiple laps in a heavy car (eg a GTR :mad:). Ive got no direct experience in that though so could be totally wrong.

As a matter of interest how much does your car weigh?

Edited by semislickR32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I am getting the same issue. Did you resolve it? I just got it after installing my new super coppermix and literally the same issue, new fork, new 18mm carrier, release bearing that came with the kit and replicated the exact same sound. 
    • If you like - I have the STL files so I can email em. There's a couple of gotchas (i.e the holes are not threaded so you might need/will need) to utilize some M3 melt-in threads for some of the points. However if you want to be super accurate, and are willing to remove your calipers and your SHOCKS it's a really good tool. You also might need to scale the part that measures the tyre width a bit wider. It defaults to a 7.5in tyre and I mean who is running that. Luckily with the magic of CAD this is very easy to rescale.
    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
×
×
  • Create New...