Jump to content
SAU Community

Recommended Posts

By the sound of it, you'd be best off spending that $1000 on a full service.

Belts, pads, fuilds (diff/gerabox) etc.

Get it reliable before you go chasing power.

exactly what i did. now i know its reliable and whats been done to it so its ready for more power :D

new power fc for bcnr33 is over a grand. Justjap has em for 1499 pls whatever they charge for postage

I should have mentioned that i just finished spending 1000.00 for the major service and changed the clutch for another 1000.00 at the same time.....

getting the bleed valve done this sat and thinking of putting in blow off valves????

sounds good???

I should have mentioned that i just finished spending 1000.00 for the major service and changed the clutch for another 1000.00 at the same time.....

getting the bleed valve done this sat and thinking of putting in blow off valves????

sounds good???

Everything is good besdies wasting money on bov. If the stock one isnt leaking then no point changing and spending a few 100 when you will get no gain.

Everything is good besdies wasting money on bov. If the stock one isnt leaking then no point changing and spending a few 100 when you will get no gain.

Thanks heaps skline01999.......

i might not waste any money on that than......

By the sound of it, you'd be best off spending that $1000 on a full service.

Belts, pads, fuilds (diff/gerabox) etc.

Get it reliable before you go chasing power.

if your car is mechanically sound, so no outstanding issues, brakes good, etc, then bleed valve, power fc, and tune.

I dissagree, factory tunning is quite ok for BPU. Without a bucket load of tuning time with the power FC the quality of the tune will never be quite like factory.

As you already have an exhaust and only 1k to spend I would install a really good FMIC add a little boost.

I should have mentioned that i just finished spending 1000.00 for the major service and changed the clutch for another 1000.00 at the same time.....

getting the bleed valve done this sat and thinking of putting in blow off valves????

sounds good???

You still got stock ceramic turbos in your GTR?

If so, don't waste money on bleed valve - just pull the restrictor (next right strut tower, there is a solenoid with 2 hose - you'll feel one of hose is bit hard to squeeze, the hose next to plenum, it may have yellow marking) pulling it off will give you safe 14psi.

Also do you have aftermarket (at least 3") front pipe?

14psi + full exhaust (don't worry about dump pipes as they're really good) + Power FC and tune = 240-250kw.

Save up a bit more and do above.

new power fc for bcnr33 is over a grand. Justjap has em for 1499 pls whatever they charge for postage

I bought mine for $1,100 with HC off ebay (Brand New). The seller was in qld. Paid another $5 for express postage. Was sitting on my door step the next day

<br />You still got stock ceramic turbos in your GTR?<br /><br />If so, don't waste money on bleed valve - just pull the restrictor (next right strut tower, there is a solenoid with 2 hose - you'll feel one of hose is bit hard to squeeze, the hose next to plenum, it may have yellow marking) pulling it off will give you safe 14psi.<br /><br />Also do you have aftermarket (at least 3") front pipe?<br /><br />14psi + full exhaust (don't worry about dump pipes as they're really good) + Power FC and tune = 240-250kw.<br /><br />Save up a bit more and do above.<br />
<br /><br /><br />

i pulled out the restrictor already....yeah, its got stocked turbo....

i might find for some good cheap power fc's on ebay :P

let me know if u guys have any ideas where to get them from as well :P

<br /><br /><br />

i pulled out the restrictor already....yeah, its got stocked turbo....

i might find for some good cheap power fc's on ebay :P

let me know if u guys have any ideas where to get them from as well :P

Just keep looking in the forum for sale section theres heaps always selling and yeah just look around ebay and stuff and youll eventally find one for around the 1000 mark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Robertson was a Canadian inventor, and it absolutely reigns supreme here. 95% of our screws are Roberston. It's literally the only option you can buy off store shelves. What would it have lost out too? I believe it's also very popular in the US.  My reference to imperial was pointed to both NPT and BSP. 
    • No. BSP lost to the cultural/technical imperialism of living next to Trumpistan. Face it, Robertson screws were better and still pretty much lost out to the yank stuff. The Europeans hate the Brits and they don't use NPT. NPT is just as "imperial" as BSP is, being based on those useless inch thingos. Just done differently. 
    • I live in Quebec. Our license plate slogan is "Je me souviens" Translated is "We will remember" as a reminder to when England conquered us and that we must never forget what they did. Long story short, BSP is unheard of here due to being an English design. I'm surprised our nazi anti english government office the OQLF hasn't kicked in my door yet just talking about it, yet alone imperial anything.       
    • Thanks for that! I did a quick Google search looked up some of hydaulic stores and didn't see it listed on the website, I'll give them a ring. Also found out later that I can buy 2 oem bleeder bolts for 10 bux and come with the washer which I might do so I don't waste the money it costs in petrol to find 2 washers (already did that lol). The old copper washes look in good nick, I drove it after taking it off and putting it back on and didn't see any  Part number here for reference if anyone needs: 14053-42L0A  
×
×
  • Create New...