Jump to content
SAU Community

Recommended Posts

Have seen a few lines and other vehicles going around with their brake calipers painted and think it looks s**t hot.

I searched past posts and came up with this thread and am just wondering if any knows if the websites listed still exist somewhere or if someone knows where i can find more of a instruction set?

Has any one done this to their own line?

Cheers

:D

Link to comment
https://www.sau.com.au/forums/topic/33277-painting-brake-calipers/
Share on other sites

Then get a propane or butane torch and gently 'melt' the paint in if you use the hi temp paint as it will be lost to wheel cleaning agents and washing unless heat cured. You could also cover all the important stuff to stop overspray. Curing this way (similar to baking in a paint oven) brings on a glossier finish.

It means stripping the caliper, which aint too big a deal if you are looking to get them rebuilt, but has anyone looked at getting them HPC coated...sure as hell would be more durable then paint, and have apparently helps reduce brake fluid temps...still i think it would be more fashion then performance for most of us

yeah, read the guide - its been covered in "maintenance" a bit.

The "curing" is not necessary actually. Mine is pretty much as good as the day i did it 4 months ago and i've washed, scrubbed, etc. The high temp paint is very durable and can cope with high temps as experienced during braking. Do 10 coats, you'll be right :D

I did mine in gloss black and it looks great but doesnt stand out.

It is infact possible to paint the calipers while they are still on the vehicle. You just have to spend a long time preparing them and masking off various areas.

Use wire brushes, steel wool and brake cleaner in an aerosol can to clean the brakes properly before painting or the paint will flake off.

With respect to the NISSAN logo, i tried two ways to leave it silver. I tried masking it off and cutting very finely with a razor blade and then i tried just spraying the whole thing and cleaning off the NISSAN logo with thinners and a rag.

The thinners+rag method worked about a million times better and gave an outstanding result if you attack the NISSAN logo while the paint is still wet.

I used VHT Brake Caliper paint which i purchased at Autobarn.

With respect to the NISSAN logo, i tried two ways to leave it silver. I tried masking it off and cutting very finely with a razor blade and then i tried just spraying the whole thing and cleaning off the NISSAN logo with thinners and a rag.
Try just painting it all and then use abit of sand paper to rub it back (after it has dried) thats how mine are done. I might re-do them again and put a gloss coat on em.

Oh and...mine says skyline in white...i painted the writing white first...then let it dry then got electrical tape and cut it out in the shape of the letters then sprayed the whole calipers blue....alot of effort cutting and stuff but well worth it :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...