Jump to content
SAU Community

Recommended Posts

OK, sorry for the lack of updates, but work got in the way for the past few months, and seeing as it finances the project, I couldn't really say no.

BETTER SAFE THAN SORRY

Having seen a fair number of incidents at the track, and also being a requirement for the race category I plan to enter, I finally bit the bullet and went the full cage. Asking around the racers in WA, one name kept popping up for who does the best rollcages. Brad Stacy. Working for one of the top Race Workshops in WA, and also working from home, I got in touch with Brad, and explained my requirements. Brad was awesome to deal with, and having done dozens of cages before I felt confident leaving my car with him.

The cage took about 2weeks, which wasn't bad considering he was doing it in his spare time. I'm really happy with the end result, and would recommend Brad to anyone thinking of getting a cage done in WA :thumbsup:

http://www.bradstacyfabrication.com.au/

Enjoy the pics

PICTURES

X side bar

post-1397-0-15130700-1308619475_thumb.jpg

Roof X bars

post-1397-0-44112300-1308619493_thumb.jpg

Front view

post-1397-0-06255800-1308619509_thumb.jpg

Rear Cage

post-1397-0-85792900-1308619525_thumb.jpg

Cage Rear Strut

post-1397-0-74825100-1308619543_thumb.jpg

Cage Hoop Top

post-1397-0-53953700-1308619565_thumb.jpg

Cage Hoop Bottom

post-1397-0-78097900-1308619580_thumb.jpg

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

Great work Paul,

Good to see Brad sorted Cage out :thumbsup: .

Whats next dude,

new RB30 :rolleyes:

I'm leaving the engine as is for the time being, makes plenty of power. Likely conversion to E85 fuel though, which should improve response and up the power a bit.

was just wondering about this car just yesturday, how long until it gets back on the track???

Potentially it could go back to the track within about 2weeks, but in order to get everything ready to pass scrutineering it will take alot longer. At least I'm back working on the car again, so progress will be made :thumbsup:

  • 4 weeks later...

just getting my battery nerd on, what are you thinking of using?

you can get pretty powerful motorbike batteries, they already use them in race/drift applications anyway

I'm getting a Braille Battery, only weights 3kg :D

http://www.autocraft.au.com/braille/index.html

bit expensive, but that is pretty light, what one were you looking at? how many cca?

are you looking at the lithium ion technology?

depending on the cca you require i'd say a Deka Powersports ETX18L or ETX30L,

they are a AGM technolgy and should have plenty of power and they could even sit around for 6 months and still start the car.

Give Goodchild Enterprises a call and they should be able to give you a good price on one, even tell them Erik from Bitz sent you

  • 2 weeks later...
  • 3 weeks later...

stock cams will do 450rwhp wouldnt ever use that much grunt really in a track car, plus you would try to retain vct at any cost possible as it is a very good thing to have while tuning.

very clean car mate did you have a dyno sheet from the engine set up on page 1?

i was also supprised at the weight of the doors as well i have mine off at the moments and there feels like enough metal to make a charade out of them.

how much weight do you think you saved by stripping the wiring harnes out of curiosity?

Edited by kungpow

paul have you disabled the VCT to run the big cams?

looking to do this to mine but cant find out much about it.

Hi Tristan, I've got the biggest VCT cams I could find, Apexi 270degs. I think the VCT is one of the best parts of the RB25s. To be honest you'll struggle to find big VCT cams, so you may be stuck with disabling it.

very clean car mate did you have a dyno sheet from the engine set up on page 1?

I do somewhere, I will try and get a copy posted up.

how much weight do you think you saved by stripping the wiring harnes out of curiosity?

At least 10kgs, I have shopping bags full of it.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...