Jump to content
SAU Community

Recommended Posts

like any brand, they have varying spring rates and quality.

from what I know they are very good value (ie relatively cheap for their quality) and are pretty good.

the problem you may face is if (like niz???) you get the superlows (low bastard lovells) and run standard shocks, you may find them bouncy.

guess it's the same with any brand. dont frig with the ride height too much unless you have a spring and damper combination which are tuned to each other.

must be my shockies then ... whatever it - they arent a good combo and will look at a redo before next summers cruising .... no point having the power but not enjoying it cos you dont have good "connection" with the road.

andrew .... unfortunately when you lower your car .... you do get "scrapage" happens to all of us .... the best way to avoid is to go up or down a curb at an angle. Im not sure about hardening up your springs ...... as far as i know that requires buying a new set of springs.

Lovells springs are pretty decent. Can't fault them really. I had some on my old car before I got adj. coilovers.....

....after that I had modified Porsche 911 rear-springs, they were uber-hard but were pretty dam good! Nowhere near as bouncy as the standard lowered lovells....

any super low set up springs suck

thats prolly why king springs only make 1 spring for the r33 which is set to a decent ride height but nothing too low because then you need the shorter shocks as well.

lovells are very good price wise also

i think malaga springs do them?

cant remember but good prices

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...