Jump to content
SAU Community

Recommended Posts

Hey Guys,

Just had the suspenioned overhauled in the r34 and looking for some sticky tyres! Car is making close to 500hp and from what i can see these are my options. any comments would be good!

Advan AD08

Nitto NT05

kumho ecsta ku36

ive also looked into semi slicks/drag radials but dont know much about what makes a good street semi slick/drag radial. Any advice would be great!

Cars one and only purpose is to go fast in a straight line.

Link to comment
https://www.sau.com.au/forums/topic/334462-best-dry-traction-tyres/
Share on other sites

looks like that is the best choice there jez, but im running 19s and it looks like the ET street II only goes up to a 18"

i know ive handicapped myself a bit with a 19" but any chance you know any 19" drag radials?

Edited by Jap_Muscle
looks like that is the best choice there jez, but im running 19s and it looks like the ET street II only goes up to a 18"

i know ive handicapped myself a bit with a 19" but any chance you know any 19" drag radials?

Any drag radial will have a higher profile than a street tyre, Its an inherent part of their design

A 19 inch drag tyre would look like a 4wd wheel. small rim and big rubber.

You would be better served by dropping to a 17 or even a 16 inch rim if drag radials are your choice. becuase of the tyre diameter they will still fill out your guards like a low profile street 19.

bang for buck the KU36's are awesome

NT05's are just amazing for street tyres (I run them on all 4's with 435rwhp) but expensive

but for drag, go a drag radial unless the car sees other use aswell

everything is a compromise mate,

only buy Mickey T's if you dont do any cornering stuff. Mickey thompsons are designed to have a super soft sidewall to obviously help hook up on launches. this is good for straight line stuff but it compromises vehicle stability and you start doing serious cornering stuff.

ku36's are shit at that power level, definately go the nittos. i just got a pair for the rear end of my r34 which will have around 600hp when finished and what the boss at tyrepower in hawthorn reckons will be the best for what i need.

ill be running the 36's on the front though as they are great for cornering and steering but not good enough to take power thru the rears.

my mate runs ku36's on his s14 with 200rwkw and i reckon they r at there limits with that. u get what u pay for .....

The KU's tread wear is more than RE001's 255's (read, they are softer, grippier)

So if RE001's are fine in my car with 270rwkw, barely breaks traction at all, then your friend needs larger tyres or some suspension/diff attention.

As is the problem with those types of examples, sometimes setups are fully correct and hence the tyres stand no chance regardless

Any drag radial will have a higher profile than a street tyre, Its an inherent part of their design

A 19 inch drag tyre would look like a 4wd wheel. small rim and big rubber.

You would be better served by dropping to a 17 or even a 16 inch rim if drag radials are your choice. becuase of the tyre diameter they will still fill out your guards like a low profile street 19.

although i do know this its starting to become outdated. what i mean by outdated is that most american muscle cars are running minimum 19" wheels and alot of companies are making 19" drag radials. Slowly but surely.

Nitto are the ones ones so far i know of though.

bang for buck the KU36's are awesome

NT05's are just amazing for street tyres (I run them on all 4's with 435rwhp) but expensive

but for drag, go a drag radial unless the car sees other use aswell

Joey i have been tossing up between the NT05 and the NT05R which is the drag radial version. being a drag radial i know a bit of what im getting myself into but im just worried the standard NT05s wont hold the power im making. do your NT05s break traction at all? what profile are you running?

everything is a compromise mate,

only buy Mickey T's if you dont do any cornering stuff. Mickey thompsons are designed to have a super soft sidewall to obviously help hook up on launches. this is good for straight line stuff but it compromises vehicle stability and you start doing serious cornering stuff.

Although i dont do any cornering (drift/track) it does get driven around on weekends and on the occasional cruise. technically it takes normal street corners and bends but i wouldnt be pushing anything. Do you see the MT ET Steets II causing me hassles in this situation?

i have been thinking about dropping down to a 18" for obvious reasons. but that wont happen till i sell my wheels. see sig for specs.

although i do know this its starting to become outdated. what i mean by outdated is that most american muscle cars are running minimum 19" wheels and alot of companies are making 19" drag radials. Slowly but surely.

His point is though i think - 19's will never be as good as a 17's equivalent, regardless of if you can buy them or not :D

It's just pure logic really and the limitations.

What gives the advantage is the sidewall. On a 19, you have less than the 17, or 16.

The tyre has to be ever softer again to even come close to matching the grip levels (if at all) & last less longer again.

If you plan to run MT ET's or similar you'll be on a 17 (not 18s) at the most to be honest as Noel said.

Can't say I've ever seen a RWD car run a 10 sec pass with 19's on it :)

yea forget the 19's man, buy some 16inch wheels put some nice drag tyres on them, throw em in the boot and swap em at the track, if u just want a decent tyre for a 19, just buy street legal semi, KU36, 595RSR they cheap and good enough, my car drives like its on rails since i straped my RSR's on

compared to nittos they r....and i stand by what i said . speaking from experience here.

Experience of what? from what I can gather it's your experience of being told what to buy by people trying to sell you stuff.

buddy im building my bottom end to handle 1000hp + so i think that my choice in buying nitto parts over the cp is a good one.

however this thread is a bout tyres if u have a problem with something i have said then pm me

cheers

Pirelli Pzero Corsa semislick, get a quote from Taleb Tyres ($150ea atm for 18's, amazing price).

treadwear of only 60! awesome tyre thats for sure, grippy, very grippy

ku36 treadwear is 160 to compare against....

edit: stag is putting out 335hp @ wheels, Im guessing thats close to 400hp at the engine prior to drivetrain loss

Pirelli Pzero Corsa semislick, get a quote from Taleb Tyres ($150ea atm for 18's, amazing price).

treadwear of only 60! awesome tyre thats for sure, grippy, very grippy

ku36 treadwear is 160 to compare against....

edit: stag is putting out 335hp @ wheels, Im guessing thats close to 400hp at the engine prior to drivetrain loss

i had the pirellis on my 19 inch vs kf on my r34 and they were grippy, just a flamin mongrel to drive with, really heavy in the front end steering feel. (due to the fact there 19's not the tyres)

buddy im building my bottom end to handle 1000hp + so i think that my choice in buying nitto parts over the cp is a good one.

however this thread is a bout tyres if u have a problem with something i have said then pm me

cheers

Umm, you are paying someone else to build it you mean :blink:

Experience of what? from what I can gather it's your experience of being told what to buy by people trying to sell you stuff.

Exactly haha

I do it for a living, and yeah someone sold him good and proper whether he likes it or not.

Anyway, why hasnt anyone mentioned RE55's in this thread? If dry traction is all the OP wants, they're great! Not a drag radial like the ET's, they're still expensive compared to KU36's etc but they're all sorts of grippy once warmed up. Life span is another story though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...