Jump to content
SAU Community

Need Full Car Sound/audio Installation

baby34

By baby34,
in Victoria

 Share

Recommended Posts

baby34 Experienced

baby34

Posted
Posted

Hi guys, finally bought my FULL sound system (Sub/Amp/Mono/Front/Rears/) *hu alrdy installed* and need someone to install it.. will drop off my car aynwhere in melbourne.. aslong as they know what they're doing and are good on price..

names & numbers pleasee

thx

rjtol Rookie

rjtol

Posted
Posted
Hi guys, finally bought my FULL sound system (Sub/Amp/Mono/Front/Rears/) *hu alrdy installed* and need someone to install it.. will drop off my car aynwhere in melbourne.. aslong as they know what they're doing and are good on price..

names & numbers pleasee

thx

try jb they can do ok prices

VSPECT Mentor

VSPECT

Posted
Posted
they're the worst =\

AGREE!!!! got them to install a dvd head unit in my car and they stuffed it up big time...the headunit is not even put in properly and was shaking big time with every ditch on the road...had to take it out and mount it on the bracket myself properly...very annoyed at that...

VSPECT Mentor

VSPECT

Posted
Posted
:D

Anyway, just a FYI - SAU-Vic members get a super priced discount on Audio install.

You'd probably save more off the install then membership would cost

we get discounts from JB for audio installs? not bad but only if they can garantee a great job on it...never had any good experience from their installations...myself and some of the guys who got their sound system installed from them were not happy...but hey if you know someone working at JB and can give us a discount and is good at their job let us know so we can only to go to that store...

S4LVA Collaborator

S4LVA

Posted
Posted

JB can do good low prices but there installs arnt the best. Known a couple of mates cars installs that had speakers held in by one screw :D. We were wondering what the rattling noise was and took it apart and there was 3 cars done like that. FreewayCarAudio Dandenongs a very good place to go. Bit more expensive but way worth it.

sympozium7 Explorer

sympozium7

Posted
Posted (edited)

Depends where you go and who you get i guess. I've used JB (Epping) and Strathfield (Thomastown). Jb installed my front & rears plus pioneer dvd touch screen player and done a very nice job, everything was neat and professionally done. They do charge a little bit but thats the price you pay for not knowing how to do it yourself.

Strathfield on the other hand... they charge a lot and dont give a damn what their installations are like. They put in my sub & amp setup with the amp jammed in next to the battery,ripped the fuse box out from next to the battery as well and cables n shiit were everywhere. Not Good. Although i feel their service is a lot better than JB's.

Edited by sympozium7

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ToothDR32
      $5 Clock upgrade for R32 GTR

      By ToothDR32 · Posted

      Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...