Jump to content
SAU Community

How Much Psi Can U Run In A Rb20det B4 Hurting It

Cyo18r

By Cyo18r,
in Engines & Forced Induction

 Share

Recommended Posts

Moodles2 Grand Master

Moodles2

Posted
Posted

Anymore than 10psi on a stock RB20 turbo, and the turbo will die. It's not about PSI either, it's about flow. A bigger turbo will outflow a smaller turbo at say 18psi. A RB20 can generally handle 200kw reliably, I generally don't see people pushing more than 250kw.

limpus Mentor

limpus

Posted
Posted

Wrong way to ask a question...its not really the amount of psi that will kill an engine...you can run 10psi which is really low and still hurt the engine if support systems are not up to scratch or the tune is off...

Look towards power figures more as a rough guide...a rb20det will happily live making 250rwkw all day every day if all is well around it...start getting to the higher reaches of 200 like around the 280rwkw mark and you will head into slightly more dangerous ground...that said...plenty or rb20s nowadays are making power in that region and still surviving nicely...and they cop a beating on a regular basis too...

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

I sexed up my fully stock RB20DET with S1 RB25DET Turbo with 16PSI all day, loved it

only mods were oil cooler, fuel pump, fmic, coil packs, ra ra ra usual bs, ecu remap

Rolls Grand Master

Rolls

Posted
Posted (edited)

It is all about flow and the tune not the psi. Pressure is just a measure of restriction, if you get your head flowed, bigger cams, larger exhaust side of the turbo and larger intake then your psi will drop but you are pushing just as much if not more air. Also you could tune a motor running 6psi so badly that it will cook itself if you try.

A better measure of is how much power the engine can make before it goes bang, assuming a perfect tune. I've seen a few 250kw+ rb20s on here last more than a few years but it all comes down to many factors.

If you are making 220kw with a safe tune with maybe 15-20psi I don't see why you couldn't get a lot of life out of it

I want sumthing that's going to cum on boost around the same rpm as a standed rb20det turbo but a turbo that will Handel say 15 - 18 psi

This is a flawed question, you should be asking what turbo for x rwkw with similar to standard response. PSI doesn't mean anything unless you specify the turbo combination. As 15psi on a small turbo will flow similar power to 8psi on a much larger turbo.

Your best bet is a steel wheeled highflowed rb20/rb25 turbo that aren't too much bigger. The lowest HP rating highflow turbos are probably your cheapest option, otherwise a 2530 etc.

These will all make 200-230kw on roughly 16psi+ although you won't have standard response, it will definitely be laggier. If you want standard response I would recommend an rb25 turbo, these can push 180-190kw with a good tune and 12psi, will only increase the lag by about 500rpm.

Edited by Rolls
  • Like 1
The Dan Grand Master

The Dan

Posted
Posted

I've seen standard CA18's run 56psi and 100+ dyno runs. Standard head gasket, standard NA pistons etc etc.

I didn't believe it when I heard but then I saw it with my own eyes.

What these guys are all telling you is true. You are probably asking the wrong question.

If you want a turbo that can run 18psi and have almost factory response then you need a highflow or a GT2860RS

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      [HOW-TO] Winter Steam-Clean & Odour Removal in 30 min

      By GTSBoy · Posted

      I'm so far behind in the jobs I have to do at both work and home (including car) that I have become immortal. There's simply no way that I can die now.
    • The Bogan
      [HOW-TO] Winter Steam-Clean & Odour Removal in 30 min

      By The Bogan · Posted

      Each to their own I guess  Me, I put just as much time into cleaning inside of the cars as I do on the outside As for getting wet, it is really no different than steam cleaning the carpets at home, apart from the cars carpet dries alot faster than the house, again, I only do it in the hotter months and leave the car opened up for a few hours As I only do it yearly, it is just before I do the diff and gearbox service, so I clean the carpets, then it's up on stands, wheels off, service, clean the undercarriage,  grease the bushings and do a nut and bolt check on everything  Disclaimer: I typically had all the time in the world to kill when I was working 🤣, so spending a full day or 2 cleaning, serving and "looking at stuff" was,  easily achievable, and a fun mental therapy day As for time to kill, I retired last Wednesday, so apart from my physical training, my days are filled with lots of random jobs around the house and garden...."Idle hands are the Devils something something" I am also buying a new house sooner rather than later, I'm actually looking at a potential property tomorrow, I'm looking forward to getting a car hoist as I'm starting to get to old to crawl around under a car, I can only imagine all the undercarriage cleaning and looking at stuff when that gets set up
    • GTSBoy
      [HOW-TO] Winter Steam-Clean & Odour Removal in 30 min

      By GTSBoy · Posted

      Yeah, I'm not interested in wetting the carpets, and I don't care about brown dirt/dust that lives deep in the pile or underneath. It's not like I crawl around on them in my birthday suit or eat dropped food off them (because there is never any open food in my car). The seats are alcantara (cheap Chinese imitation alcantara, to be sure!) with barely 1" of foam pad behind the surface. That's not getting wet either. Any car that I would be happy to get the interior wet, I would not care to put the effort into.
    • MBS206
      [HOW-TO] Winter Steam-Clean & Odour Removal in 30 min

      By MBS206 · Posted

      We have one that holds 2.8L of water. On floor carpet that hasn't been touched in 2 or 3 years, will take a minimum of 2 fills of the tank to do a bedroom, and that's going AROUND the bed.   In the cruiser, I used an ENTIRE 2.8L tank, just on the front passenger footwell. But it had some fungus growing, and had been full of mud from being used as a 4WD for many years. I can do that floor again, and it will still pull mud out. However, the water now only looks dirty, not pitch black and leaving full sludge in the bottom of the tank it sucks back into. Oh, and, this is about a $1500 unit.
    • The Bogan
      [HOW-TO] Winter Steam-Clean & Odour Removal in 30 min

      By The Bogan · Posted

      This is mine, works a treat for the cars, suction is good, I use the Bissell clean and protect stuff I have found giving it a good spray and light scrub with the soft brush on the head of the nossle for carpet, and a rub with a microfibre for cloth seats and cloth door trims, prior to another quick spray before vacuuming it up works the best @GTSBoy You would surprised on what it gets out of carpet and seats that actually "look" clean, I recommend that you test drive yours when you have a little time to kill, then post pics of the muddy looking water that I believe you will find
×
×
  • Create New...