Jump to content
SAU Community

Recommended Posts

Anymore than 10psi on a stock RB20 turbo, and the turbo will die. It's not about PSI either, it's about flow. A bigger turbo will outflow a smaller turbo at say 18psi. A RB20 can generally handle 200kw reliably, I generally don't see people pushing more than 250kw.

Wrong way to ask a question...its not really the amount of psi that will kill an engine...you can run 10psi which is really low and still hurt the engine if support systems are not up to scratch or the tune is off...

Look towards power figures more as a rough guide...a rb20det will happily live making 250rwkw all day every day if all is well around it...start getting to the higher reaches of 200 like around the 280rwkw mark and you will head into slightly more dangerous ground...that said...plenty or rb20s nowadays are making power in that region and still surviving nicely...and they cop a beating on a regular basis too...

I sexed up my fully stock RB20DET with S1 RB25DET Turbo with 16PSI all day, loved it

only mods were oil cooler, fuel pump, fmic, coil packs, ra ra ra usual bs, ecu remap

It is all about flow and the tune not the psi. Pressure is just a measure of restriction, if you get your head flowed, bigger cams, larger exhaust side of the turbo and larger intake then your psi will drop but you are pushing just as much if not more air. Also you could tune a motor running 6psi so badly that it will cook itself if you try.

A better measure of is how much power the engine can make before it goes bang, assuming a perfect tune. I've seen a few 250kw+ rb20s on here last more than a few years but it all comes down to many factors.

If you are making 220kw with a safe tune with maybe 15-20psi I don't see why you couldn't get a lot of life out of it

I want sumthing that's going to cum on boost around the same rpm as a standed rb20det turbo but a turbo that will Handel say 15 - 18 psi

This is a flawed question, you should be asking what turbo for x rwkw with similar to standard response. PSI doesn't mean anything unless you specify the turbo combination. As 15psi on a small turbo will flow similar power to 8psi on a much larger turbo.

Your best bet is a steel wheeled highflowed rb20/rb25 turbo that aren't too much bigger. The lowest HP rating highflow turbos are probably your cheapest option, otherwise a 2530 etc.

These will all make 200-230kw on roughly 16psi+ although you won't have standard response, it will definitely be laggier. If you want standard response I would recommend an rb25 turbo, these can push 180-190kw with a good tune and 12psi, will only increase the lag by about 500rpm.

Edited by Rolls
  • Like 1

I've seen standard CA18's run 56psi and 100+ dyno runs. Standard head gasket, standard NA pistons etc etc.

I didn't believe it when I heard but then I saw it with my own eyes.

What these guys are all telling you is true. You are probably asking the wrong question.

If you want a turbo that can run 18psi and have almost factory response then you need a highflow or a GT2860RS

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...