Jump to content
SAU Community

Recommended Posts

I didn't think anyone was compliancing 34 R's yet.

Some story about GTT and GTR having to be done as separate vehicles?

Come to think of it - didn't know anyone was doing 34 GTTs yet either...

nah nobody is doing the R34's yet NOBODAY and wont be for a couple of months. Its taking th GOV 6 months just to get to work shops to look over and acept there evidence. Lets say the first person to get them will be charging around $6,000 id say. And they will be able to get it to. So you find me a compliance company that can do it and we will buy 10 plates.

Also if you want go to the DOTARS website to look what cars are up. Only the R33's are eligble. And I dont think anybody is going to be doing the R32's but I did se a 4 door and a 2 door down at the docks today that were not 89's so maybe someone is doing the crash tesing on them. Damn I hope.

R34's are selling for 3million+ Yen (~$AU38K). No one is complying 34's at the moment. As soon as one gets RAWS approval I would wait a month or two - alot of people are going to get approval, just waiting on the 1st person to get through so they can use alot of their information to pass their own workshop.

They're SEVS eligible to come in and under the R34 series just about everything that meets the power ratio bullshxt can come in under one set of evidence (or so I've been lead to believe by the workshops I work with..) Two workshops here in Sydney who's doing the R33 said they were going to get the R34's done by March but the hardass engineer down in DoTaRS don't like what they saw...one workshop failed the intrusion bars last week.

$6k for complying R34's sounds a bit optimistic, one workshop have whinged about the evidence cars for R34 cost a lot more than the R33's which is true.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...