Jump to content
SAU Community

Recommended Posts

After checking where the sump plug was on my car (only owned it for a month) I noticed the transmission looks like its got a short bolt going through it. Not sure if this is normal, It doesn't look right. Anyone else s like this? The clutch has been changed so maybe they lost the propper screw and put this little one in. Or is this how its meant to be?

post-74152-1284302641_thumb.jpg

post-74152-1284302651_thumb.jpg

post-74152-1284302658_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/336583-short-bolt/
Share on other sites

Its done up nice and tight. Now i've just realised my car jacks about half a cm to high to fit under the front of my car. How are car ramps for oil changes? Seems much easier driving up some ramps compared to jacking the car up. Just not sure if theyd fit under the car either. Also cant find a good spot to jack the back of the car.

Have i got the right spot for the front jack to go?

For the back I just cant see a strong enough spot.

post-74152-1284353665_thumb.jpg

post-74152-1284353681_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/336583-short-bolt/#findComment-5444054
Share on other sites

i used to jack my 33 up from various locations. for the front you could use where you circled in the pic (having a brain fart at the moment and can't remember the name of it), or you can jack it from a few locations around the wheel where the suspension parts bolt to the body.

for the rear the same goes. there are a few suspension points you can jack from, or even the diff if need be.

Link to comment
https://www.sau.com.au/forums/topic/336583-short-bolt/#findComment-5444097
Share on other sites

I use some scraps of 2" thick pine - drive the car (front or rear, works for both ends) up onto the block, then you have enough clearance to get a trolley jack under.

I use the cross member for the front, and the diff for the rear. Generally, ramps are too steep to allow the front bar to clear the ramps.

For an oil change, jack the car, then use axle stands under the LCA, then remove the jack (because it gets in the way of the oil draining into the catch tub).

Link to comment
https://www.sau.com.au/forums/topic/336583-short-bolt/#findComment-5444208
Share on other sites

I was looking for ways to try make this jack fit under the car for a good 2 hours.Went looking at car ramps at autobarn,supercheap,repco bursons and tool shops but they were all too high for the front of the car. Then my brother came home and just put a scissor jack on the side and jacked the front lol. Duno how I didn't think of that ;)

Link to comment
https://www.sau.com.au/forums/topic/336583-short-bolt/#findComment-5445050
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...