Jump to content
SAU Community

What Have I Missed?

nuclear_skyline

By nuclear_skyline,
in Engines & Forced Induction

 Share

Recommended Posts

nuclear_skyline Mentor

nuclear_skyline

Posted
Posted

Hi Guys,

I am about to pull the engine out of my 94' BNR32. Basically I am looking for some advice as to what I have missed given that I am only seeking 250-280rwkw (ands thats in the future not now). I am primarily looking for reliability atm.

So here is what I have:

-water pump

-gates timing belt and new ilder bearings

-new turbos

-new dump pipes

-new silicon heater hose kit

-bought a full engine gasket kit so I can do the gaskets for the plenum.

I think I should get a sump baffle whilst the engine is out. I just cannot decide what one! I have been looking at the tomei one that fits in the standard sump.

Thanks for your input guys.

Link to comment
https://www.sau.com.au/forums/topic/336830-what-have-i-missed/
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

If you only want 280rwkw then you don't need to change dumps, sump mods.

Also be careful when changing the plenum gasket. I do believe there is a "trick" to get it to seal correctly. Do not clean the butterflies etc either.

Also the silicone heater stuff I've found to be crap. I've had to replace 3 hoses in 1.5years and I've done less than 10,000kms.

It's one of your typical EBAY special's. It's been replaced this time though with Nissan OEM hose :geek:

nuclear_skyline Mentor

nuclear_skyline

Posted
  • Author
Posted

Cheers Ash - I have a pretty good mechanic, one I actually used to work for at revo, but we'll definately be careful on the plenum. I have heard that the standard gaskets can become very brittle as they age and have a tendency to split (CRD and JustJap told me).

I got a very good price on the dumps so thought I might as well pick them up now - who knows what will come in years to come?

Also cheers on the heads up re silicon hoses - is the issue that they perish quickly or that they cannot handle heat? Any incites?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Yep - they do fail, and just as much of a pain to replace so good thing to do if the motor is out.

Also get the paint tidy'd up as well :geek:

Fair enough if you got a good price :D

I kept getting pin hole leaks which then results in coolant being sprayed all over the place.

From what i could tell the hoses are a bit thinner, and there isn't a lot of the webbing inbetween the silicone layers when you slice it open.

So obviously lacking support and durability/quality.

3rd time it happened it was the straw for me so went with OEM hose that was modded to suit.

nuclear_skyline Mentor

nuclear_skyline

Posted
  • Author
Posted

Oh most definately the paint is going to get a tidy up :geek: one of the reasons of buying a full gaskit kit is I can paint all the parts properly. But as it is not a genuine reliability mod I didnt think to post it :D

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Why are you pulling the engine out? How many km has it done? If you're going to take the sump off (and the head?) you may as well do rings and bearings. Replace and correctly torque the tensioner bolt when you do the cam belt etc.

nuclear_skyline Mentor

nuclear_skyline

Posted
  • Author
Posted
Why are you pulling the engine out? How many km has it done? If you're going to take the sump off (and the head?) you may as well do rings and bearings. Replace and correctly torque the tensioner bolt when you do the cam belt etc.

Honestly, who knows how many Kms their car has done!? The engine is coming out for a few reasons. Firstly, as stated above I am doing my turbos and from the advice I have received from many people is it is just as quick to pull the engine and do them out of car. Secondly, I wanted to do the heater hoses and the vaccum lines for the engine - basically undoable with the engine in place. My gearbox is making some interesting noises which make me think the input bearing is a bit dodgey so I want to overhaul it as well. Its easy to service out of car.

Regarding doing the bearings and rings. Hmmm... The engine compression is good and it isnt using any oil. I am not planning on building a power monster so i cannot justify opening it up to that extent. Lastly and most importantly, the age old question - where do I stop? If I did the rings and bearings, I most likely couldnt justify the hassle of doing it without new throwing in some forged slugs. Then, if I am doing that should I hone the block, check the crank, have the head once overed, etc.... Basically not what I am aiming for atm.

nuclear_skyline Mentor

nuclear_skyline

Posted
  • Author
Posted

Yeah the machining costs add up - which inevitably means you want to put the best parts in to make the most of it... luckily I'm not going down that route just yet :D

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Ye the age old "where do you stop" is certainly real :whistling:

You'd be @ 4k before you began, then no point going those turbos... AFM changes, injectors and suddenly 10k+ has walked out the door!

Ripping the motor to do what you wanna do - is very ideal and smart.

Plenum & hoses are a pain in the ass and much easier outside the car as are turbos.

Overall cost would IMO, be cheaper labour wise as it doesnt take that long to get the motors in/out with experienced people.

nuclear_skyline Mentor

nuclear_skyline

Posted
  • Author
Posted

Luckily my labour cost is $0 :whistling: Allows more parts to be bought. Ash - do you reckon the tomei sump baffle is worthwhile? I dont think I need to go to a larger winged sump, but as I might track it in the future the sump baffle is needed?

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Honestly having seen cars running sticky rubber and a lot more power than you - they all did it stock sumps and 1litre overfilled.

So I'd say no. But it's your call but without doing the other head/oil mods etc, that's where the real problems are anyway

nuclear_skyline Mentor

nuclear_skyline

Posted
  • Author
Posted

I have kinda been scared about putting an N1 pump on from the horror stories (i know many people have had success as well). I wasnt going to do an oil restrictor as I wasnt planning on cracking the engine open.

Does the N1 provide higher pressure / greater L/min?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...