Jump to content
SAU Community

96 Series Ii 33 Gtst Shuddering And Screetching

hks33
 Share

Recommended Posts

hks33 Experienced

hks33

Posted
Posted

hey sau,

love this site and appreciate everyones help alot, i recently have got my brake pads machined and replaced but for some reason when i apply sufficient force to the brakes i can hear like a screeching similair to the sound of worn pads... its only coming from the front discs im fairly sure they arent worn allready and not sure what it could be since i have recently changed all four

regards chris

i forgot to mention the car shudders and shakes when slowing down and force is put on the brake

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

the discs are warped or the discs mounting surface has rust on it causing it to not seat perfectly flat

, did you get a mechanic to replace the pads and machine the discs?

take it back and ask them to check it for u. they shouldnt charge you anything if they were done recently.

other than that if they were not bedded in correctly they might be glazed and warped from any hard braking you have done.

hks33 Experienced

hks33

Posted
  • Author
Posted

hopefully there not warped there not rusty either because had all 4 replaced and machined recently its just the noise the front two or front one which is a problem

Dobz Experienced

Dobz

Posted
Posted

If they were working ok ei. not shuddering or screeching before then they started it would be due to improper wear in of the pads. If you don't wear the pads in properly they glaze as DVS32R said. Glazing makes them squeel, then over heats your rotors causing them to warp and gives you shudder.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...