Jump to content
SAU Community

Recommended Posts

Hey Guys,

I need some help here with my ECU choice.

I have a Motec M800 + Motec CDI that I am running in one of my race cars. Great ECU, very happy with the tune and control - NOT HAPPY about paying for bullshit extras that should be included (launch control, anti lag, logging etc). I have the basic setup and logging enabled and advanced functions is around $500 on top, which I will buy for anti lag and launch control when the car is finished after the new turbo install.

I can spend cash and and get a new loom made up for the daily drive and just have the motec plug in and plug out whenever I need to get the race car sorted. I can only drive one car at a time so this is fine, however I was thinking that a VIPEC V88 would be a good upgrade for the daily, cost around $2500 or so trade with sensors etc and I get all the goodies factory (anti lag launch control etc).

Just how good is the V88? Is it as good as or better than the motec? The software looks easy to follow and there are heaps of options enabled as well as factory additions that increase the functionality. I would like to try something new like the VIPEC in the future anyway and my conversion/switching costs is around $1000 for a new Motec flying loom + CDI Loom + 3bar map sensor and a few other basic sensors to make it plug and play. So for around $1500 after switching costs, I get a new ECU and a new toy to play with, with all the features that would cost THOUSANDS to enable on a motec.

What are your thoughts?

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

I have considered Autronic, but it is too archaic for my liking and the software sucks.

The newer haltech platinum did cross my mind as well. Software looks fancy, however not sure on the tune/functionality - anyone got feedback on the newer haltech?

i removed my m600 and cdi and now run a vipec v88 and m&w cdi in the godzilla drag gtr ...runs the engine the same..

if it was not up to the job i would not run it on my 30grand engine..

hope this helps. mark godzilla motorsport..

Hey Guys,

I need some help here with my ECU choice.

I have a Motec M800 + Motec CDI that I am running in one of my race cars. Great ECU, very happy with the tune and control - NOT HAPPY about paying for bullshit extras that should be included (launch control, anti lag, logging etc). I have the basic setup and logging enabled and advanced functions is around $500 on top, which I will buy for anti lag and launch control when the car is finished after the new turbo install.

I can spend cash and and get a new loom made up for the daily drive and just have the motec plug in and plug out whenever I need to get the race car sorted. I can only drive one car at a time so this is fine, however I was thinking that a VIPEC V88 would be a good upgrade for the daily, cost around $2500 or so trade with sensors etc and I get all the goodies factory (anti lag launch control etc).

Just how good is the V88? Is it as good as or better than the motec? The software looks easy to follow and there are heaps of options enabled as well as factory additions that increase the functionality. I would like to try something new like the VIPEC in the future anyway and my conversion/switching costs is around $1000 for a new Motec flying loom + CDI Loom + 3bar map sensor and a few other basic sensors to make it plug and play. So for around $1500 after switching costs, I get a new ECU and a new toy to play with, with all the features that would cost THOUSANDS to enable on a motec.

What are your thoughts?

you say it's for a daily.... why not just go a good old second hand pfc?

vipec/motec are definately better ecu's but when you have a race car, how much do you really need on the street?

JJJ: engine is a 1.5JZ, PFC for a 1JZ is around 1500 or so - not worth it for such a limited ECU that is limited to a hand controller. FC datalogit software will bring it up close to the cost of a V88. Looking at making around 350rwkw with a T04Z and HKS 264/272 cams and I'll borrow the 800cc injectors while I upgrade the fuel system on the race car for E85.

Walk510: Yes the factory motec datalogging software is great, but if you want to overlay graphs etc - you need pro, more $$$.

Sounds like the V88 is a winner for a race/daily setup. I love the Motec, but it does come at a high premium with marginal added value compared to today's ECUs tune and standard features. Fantastic back in 2001, but its 2010 now and there has been a lot of inroads into ECU tech to try and beat Motec at their own game.

Motec themselves are working on ECU's to tune direct injection and so forth - the next generation of engines.

Currently waiting for quotes on a flying loom and so forth to see how much it would cost to re-wire the CDI and Motec instead of getting a new ECU, however I believe that this exercise could cos as much as a v88 in itself given today's prices.

On another note - what is the v88 knock sensor option like? How does it compare to the Gizmo k-mon?

You already have the motec and it is $500 for the extras but a Vipec is worse and costs $2500? Why on earth would you pay more for less? Am I missing something here?

A Motec is 1000x better and easier to tune properly than any other ECU on the market, and if it is going to cost less for the extras then I don't see why you would downgrade to something else. Personally if you already have made the outlay and paid for installation and tuning I would not change.

If you were considering both from scratch then I would cost up both options and consider the Vipec. How many of the extra features would you need? Do you really need launch control etc?

Edited by Rolls
You already have the motec and it is $500 for the extras but a Vipec is worse and costs $2500? Why on earth would you pay more for less? Am I missing something here?

Lol... Yes, a lot.

The fancy logging with the Motec is impressive and the reason why a lot of people still use them. The Vipec will get there but it is still a new product and is continuing development.

Lol... Yes, a lot.

The fancy logging with the Motec is impressive and the reason why a lot of people still use them. The Vipec will get there but it is still a new product and is continuing development.

I realise the vipec is a great ECU but the motec is still better if he already owns it then I am confused why spending more to get less is being considered?

I realise the vipec is a great ECU but the motec is still better if he already owns it then I am confused why spending more to get less is being considered?

How is the Motec better? Better at what? Vipec has a faster processor and is more accurate, operates at greater temperature extremes... do some reading or at least drive a car tuned with an M800 and one with a V88.

He could sell the M800 with everything and get a V88 with all motorsport options, installed and tuned for the price he sold it for.

A Motec has far superior tuning software, Ive used a few and nothing even comes close. If he does sell the motec will he get many extra features that will be used? If not I would stick with the motec purely due to how much easier they are to tune.

Edited by Rolls
If not I would stick with the motec purely due to how much easier they are to tune.

That is surprising, not in my experience. But each to their own.

To the OP Vipec V88 uses the standard knock sensors, works fine.

That is surprising, not in my experience. But each to their own.

To the OP Vipec V88 uses the standard knock sensors, works fine.

Yeah I've changed my tune after a bit of reading, by the time you buy the wideband support, knock sensor support blah blah it certainly is going to be prohibitive to buy. I think the Vipec would be better bet even if it isn't as easy to tune, but I guess that comes down to the tuner anyway.

How is the Motec better? Better at what? Vipec has a faster processor and is more accurate, operates at greater temperature extremes... do some reading or at least drive a car tuned with an M800 and one with a V88.

He could sell the M800 with everything and get a V88 with all motorsport options, installed and tuned for the price he sold it for.

ummm were is dirtgarage when you need him for some good old motec bashing ??? bigmikespec has you idol gone away ? someone has too keep up the fight and it may as well be you now ?

what ecu does swiper the fox's car have now ??? not the inferior one does it ?

even mark is his gtr still run's an motec adl3 and motec e888 to measure the greater temperature extremes you talk about

how many real top level motorsport cars run motec I mean REAL race cars i.e dakar,rally raid,alms then to the national stuff like aus safari,finke,arc,super taxi's

class 1 offshore power boats and the list goes on and on

don't these class's operate in the most rugged extremes of the environment has to offer BUT the vipec is still better

but vipec make you car idle so much better like when does that really matter racing is Wide Open Throttle where it's meant to matter

ummm were is dirtgarage when you need him for some good old motec bashing ??? bigmikespec has you idol gone away ? someone has too keep up the fight and it may as well be you now ?

what ecu does swiper the fox's car have now ??? not the inferior one does it ?

even mark is his gtr still run's an motec adl3 and motec e888 to measure the greater temperature extremes you talk about

how many real top level motorsport cars run motec I mean REAL race cars i.e dakar,rally raid,alms then to the national stuff like aus safari,finke,arc,super taxi's

class 1 offshore power boats and the list goes on and on

don't these class's operate in the most rugged extremes of the environment has to offer BUT the vipec is still better

but vipec make you car idle so much better like when does that really matter racing is Wide Open Throttle where it's meant to matter

Lol... did I say it was inferior? I am not bashing it either, read what I said.

I spoke to Paul "re" Motec and the reason he changed back was for the logging, that being said, the logging is great better than the Vipec at this stage.

I was in a position to buy either, I went in cars with both, my tuner sold both... I chose Vipec

Don't be so naive :blink: motorsport has more to do with sponsorship and marketing than what products perform better.

PS: my comment was regard to operating temperature of the unit itself not measuring

PSS: I would run an ADL3 with my Vipec it is an awesome unit, it is compatable with the V88

ummm were is dirtgarage when you need him for some good old motec bashing ??? bigmikespec has you idol gone away ? someone has too keep up the fight and it may as well be you now ?

what ecu does swiper the fox's car have now ??? not the inferior one does it ?

even mark is his gtr still run's an motec adl3 and motec e888 to measure the greater temperature extremes you talk about

how many real top level motorsport cars run motec I mean REAL race cars i.e dakar,rally raid,alms then to the national stuff like aus safari,finke,arc,super taxi's

class 1 offshore power boats and the list goes on and on

don't these class's operate in the most rugged extremes of the environment has to offer BUT the vipec is still better

but vipec make you car idle so much better like when does that really matter racing is Wide Open Throttle where it's meant to matter

Am I the only one that had trouble reading this?

Try to use some decent grammar mate, your post sounds like it was typed by someone with ADD.

Lol... did I say it was inferior? I am not bashing it either, read what I said.

I spoke to Paul "re" Motec and the reason he changed back was for the logging, that being said, the logging is great better than the Vipec at this stage.

I was in a position to buy either, I went in cars with both, my tuner sold both... I chose Vipec

Don't be so naive :rofl: motorsport has more to do with sponsorship and marketing than what products perform better.

PS: my comment was regard to operating temperature of the unit itself not measuring

PSS: I would run an ADL3 with my Vipec it is an awesome unit, it is compatable with the V88

wasn't there real reason Paul went to motec ???? it can't just be about logging

I'm happy you chose vipec congratulations !!

I'm not naive i just cant stand the crap that some people carry on about

Motec don't sponsor anybody EVERYONE has to pay for it vipec on the other hand i dont know

P.S whats your story about operating temperature of the unit ???

PSS how is the vipec more accurate ?????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I havent bought a manual cover for the dash yet and no cluster change, won't bother me too much, I just need to get that auto box gone, manual in! I miss my manual. 🤪. We started last weekend and managed to get the box out. Planning to start putting it in this weekend and then order a single piece tail. We were super careful to take time and not damage anything. It's my first time working under the car.  With my S15 mainly worked in the bay. This time, it was a headache because of three or four bolts only. They simply didnt want to leave thei homr and the one securing the tailshaft, another above the GB, and the one securing the lipstick was a shit. Mates mate, Davo caught fire 🤣, nearly opened his chest up with a grinder 🤦🏽‍♂️ and both mates nearly had a plate from the box land and slit their head open. Fun times. We all survived. Not the easiest working with limited access on jackstands. As I'm sure we can agree these are the memories which make us love our car. For all three of us, was an awesome weekend and Sunday 3.30am before tools down was a fantastic effort. I need to upload pics, but looks like it needs to be via Url now. We used to be able to just upload pics back in the day. It's been that long! 🤪 Im currently spraying rustoleum under body, not because it's rusted. It's super clean, but just so it's protected for the next 10 years. There was a few surface rust spots. Which pretty much wiped off with a 3M scourer.  Really impressed with how well the previous owner maintained it. Bank account went down so quick! Service, then GB - managed to get a spanking new 34 genuine box from Nissan. All the rest of the conversion parts from Kudos.  Went with a Nismo short shifter. New pedals and Exedy Clutch and FW. Ordered the Prp Rear Main Retainer kit which should arrive Friday and my first engine mod part just like I did with my S15 will be the Tomei Expreme Turbo Outlet. Already on order. It'll likely sleep next to me on a pillow during the coming months. 🥰 Last build was on my JET200GT profile and on SAU and Hardtuned I had documented the build. Planning to try to do that again. Brands feel scarce now. Wish we still had ARC and Apexi parts readily available. Exhaust - need some advice on this. I had an Apexi exhaust on the S15 and loved the tone. My mate had a HKS HP Silent on his 33 and suggested I go with that to avoid drone. I can't remember hearing an RB25DET running that so will likely need to wait for a meet or something to hear it.  Not after big power, just enjoy building it, and drivability with minimal negative attention.
    • Have a chat with Ben at Moore Performance or Jesse at JS Performance.
    • Thanks both. All good advice. Reminds me of drilling through stone wall for drainage pipe 😬 I'll let you know how I get on if I still have use of my hands afterwards 😅
    • Finally got shipping number for the intake and throttle body, shipped by UPS, so "should" be in my hands sometime next week, fingers fracking crossed
    • I'm so far behind in the jobs I have to do at both work and home (including car) that I have become immortal. There's simply no way that I can die now.
×
×
  • Create New...