Jump to content
SAU Community

Putting The Headlight Caps Back On With Hids?

TUF250

By TUF250,
in Exterior & Interior Styling

 Share

Recommended Posts

TUF250 Proficient

TUF250

Posted
Posted

Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

Mr Eps Grand Master

Mr Eps

Posted
Posted

...sorry to get all "dad" on you here...

but R33 have reflector headlights.. HIDs are generally used on projector headlights because of the single direction that projectors give..

generally speaking- R33 have reflectors.. and - VERY badly corroded headlight lenses.. a lot of people will opt for HID because their lights are "weak"

a lot of the "weakness" is because people don't take care of their headlights, when you put HIDs on them - it just makes the problem worse because you have even MORE light which shines off in every other direction.. which is gay..

all i'm saying is - if you went a ghetto plug n play HID kit - i hope you cleaned and reonditioned your headlights FIRST... if not - RECONDITION them!!!!

Mr Eps Grand Master

Mr Eps

Posted
Posted

to summarize on reflector lights the light showers here there and every where. it gets a lot worse when the lens isn't crystal clear... light literally dissipates into a million thousand different directions.. one kit I recommend is glassylite.. 40 a kit and it gets best results ever.. available from auto1.. my results are in attached picture.. sorry to off topic you but i'm just saying hid isn't the only answer.. you should recon lenses even as support..

post-13494-1286173981_thumb.jpg

post-13494-1286174090_thumb.jpg

Charles89 Grand Master

Charles89

Posted
Posted
Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

To reply to your question, what you were meant to do was actually cut a big hole on cap, so you can fit all your wires and stuff through.

Not sure about your HID kit, but mine came with a litte rubber plug, that plugs into that big hole that you'd cut, so nothing can get into the headlight.

If your HID kit didn't come with the rubber plug, then I guess use some sort of tape or something.

RusH_ Veteran

RusH_

Posted
Posted
To reply to your question, what you were meant to do was actually cut a big hole on cap, so you can fit all your wires and stuff through.

Not sure about your HID kit, but mine came with a litte rubber plug, that plugs into that big hole that you'd cut, so nothing can get into the headlight.

If your HID kit didn't come with the rubber plug, then I guess use some sort of tape or something.

+1 to this

TUF250 Proficient

TUF250

Posted
  • Author
Posted

AHA! thats what that rubber plug is for! It wasnt explained in the instructions, that makes perfect sence now. I will do that next week. Thanks for that!

In reference to my headlights I have used the restore kit and my lenses are in great, near new looking condition. The reflaectors appear in very good condition and mine is a genuine low k one aust owner car which prob helps. I only bought HIDs because i like the look and do a bit of night driving so the extra light helps

thanks guys!

.:: GimpS-R34 ::. Grand Master

.:: GimpS-R34 ::.

Posted
Posted

drive up the road.. and get a mate to drive towards you and see if the light gets in his eyes... some lights arent designed for HIDs and glare horribly in others eyes.. check if yours do this as its dangerous and f**king annoying..

NYTSKY Grand Master

NYTSKY

Posted
Posted
Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

Just put a slight notch on the side of the cap, then slide the wire into the notch. This will enable you to put the cap back on without squashing the wire.

Charles89 Grand Master

Charles89

Posted
Posted
it wasn't explained in the instructions??

it's probably because your instructions looked a bit like this..

hieroglyphics.jpg

I think that says.... put a bird into your headlight and it will hold your HID bulb in place? No? lol

PIG747 Mentor

PIG747

Posted
Posted
Just put a slight notch on the side of the cap, then slide the wire into the notch. This will enable you to put the cap back on without squashing the wire.

i fitted a set last night and did the exact same thing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Predator1
      Rb26 iron block limit

      By Predator1 · Posted

      Why not? Since mines been built, I've used low boost maybe 5 times.
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Yeah, so widen your search to any Nissan speedo first, then go wider if needed. I will say though, that there is a better than even chance that what I said first will likely come into play. They quite possibly won't come apart without damage. I tried to disassemble a stepper gauge that I wanted to repair. There was no way that needle was coming off the spindle, and I could not see how the spindle would come out of the mechanism behind. Assembled once, never to be disassembled, was my conclusion. Could be the same on the R34 cluster. Failing that - take the cluster to a workshop that specialises in automotive instrument work. There's usually at least one in every Australian city. They'll either be able to do it for you for small cost, or tell you it can't be done. It might be that "it can't be done" unless you follow some arcane procedure, including trickiness to glue it back together or something, that only experienced techs know.
    • GTSBoy
      R-chassis INNER tie rod torque spec?

      By GTSBoy · Posted

      Well, given that I, an engineer, almost never bring out the torque wrench to tighten up chassis bolts, despite fully knowing the theory, and instead rely on feel, which I happen to know is exactly how the majority of mechanics do things, should tell you the level of actual peril that exists from not achieving exactly 88 Nm of torque. How about if I just say then that 88Nm is at the lower end of the correct wheel nut torque range? Everyone knows how to tighten a wheel nut, right? And almost no-one ever brings out the torque wrench for that task
    • hardsteppa
      R-chassis INNER tie rod torque spec?

      By hardsteppa · Posted

      Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • JC71
      gauge needle removal

      By JC71 · Posted

      I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
×
×
  • Create New...