Jump to content
SAU Community

Putting The Headlight Caps Back On With Hids?

TUF250

By TUF250,
in Exterior & Interior Styling

 Share

Recommended Posts

TUF250 Proficient

TUF250

Posted
Posted

Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

Mr Eps Grand Master

Mr Eps

Posted
Posted

...sorry to get all "dad" on you here...

but R33 have reflector headlights.. HIDs are generally used on projector headlights because of the single direction that projectors give..

generally speaking- R33 have reflectors.. and - VERY badly corroded headlight lenses.. a lot of people will opt for HID because their lights are "weak"

a lot of the "weakness" is because people don't take care of their headlights, when you put HIDs on them - it just makes the problem worse because you have even MORE light which shines off in every other direction.. which is gay..

all i'm saying is - if you went a ghetto plug n play HID kit - i hope you cleaned and reonditioned your headlights FIRST... if not - RECONDITION them!!!!

Mr Eps Grand Master

Mr Eps

Posted
Posted

to summarize on reflector lights the light showers here there and every where. it gets a lot worse when the lens isn't crystal clear... light literally dissipates into a million thousand different directions.. one kit I recommend is glassylite.. 40 a kit and it gets best results ever.. available from auto1.. my results are in attached picture.. sorry to off topic you but i'm just saying hid isn't the only answer.. you should recon lenses even as support..

post-13494-1286173981_thumb.jpg

post-13494-1286174090_thumb.jpg

Charles89 Grand Master

Charles89

Posted
Posted
Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

To reply to your question, what you were meant to do was actually cut a big hole on cap, so you can fit all your wires and stuff through.

Not sure about your HID kit, but mine came with a litte rubber plug, that plugs into that big hole that you'd cut, so nothing can get into the headlight.

If your HID kit didn't come with the rubber plug, then I guess use some sort of tape or something.

RusH_ Veteran

RusH_

Posted
Posted
To reply to your question, what you were meant to do was actually cut a big hole on cap, so you can fit all your wires and stuff through.

Not sure about your HID kit, but mine came with a litte rubber plug, that plugs into that big hole that you'd cut, so nothing can get into the headlight.

If your HID kit didn't come with the rubber plug, then I guess use some sort of tape or something.

+1 to this

TUF250 Proficient

TUF250

Posted
  • Author
Posted

AHA! thats what that rubber plug is for! It wasnt explained in the instructions, that makes perfect sence now. I will do that next week. Thanks for that!

In reference to my headlights I have used the restore kit and my lenses are in great, near new looking condition. The reflaectors appear in very good condition and mine is a genuine low k one aust owner car which prob helps. I only bought HIDs because i like the look and do a bit of night driving so the extra light helps

thanks guys!

.:: GimpS-R34 ::. Grand Master

.:: GimpS-R34 ::.

Posted
Posted

drive up the road.. and get a mate to drive towards you and see if the light gets in his eyes... some lights arent designed for HIDs and glare horribly in others eyes.. check if yours do this as its dangerous and f**king annoying..

NYTSKY Grand Master

NYTSKY

Posted
Posted
Hi all. I just bought some HIDs for my r33 skyline. They are great, really pleased.

but... the new wiring for the new globes means that I cannot get the caps back on the headlights as the new wiring will be squashed. really didnt want to hack up the wire so I can return it to stock if i have to. needs the caps because i dont want dust or water in there.

any good ideas from people who have done this before? pics would be awesome

thanks

Just put a slight notch on the side of the cap, then slide the wire into the notch. This will enable you to put the cap back on without squashing the wire.

Charles89 Grand Master

Charles89

Posted
Posted
it wasn't explained in the instructions??

it's probably because your instructions looked a bit like this..

hieroglyphics.jpg

I think that says.... put a bird into your headlight and it will hold your HID bulb in place? No? lol

PIG747 Mentor

PIG747

Posted
Posted
Just put a slight notch on the side of the cap, then slide the wire into the notch. This will enable you to put the cap back on without squashing the wire.

i fitted a set last night and did the exact same thing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
×
×
  • Create New...