Jump to content
SAU Community

Recommended Posts

My car is having issues where sometimes the rev's would just fluctuate by itself and then eventually just cut off (while driving or on idle). I would try to start it up again and it would crank the first 2 times, then eventually nothing would happen when you turn the key (no click, no sound at all).

To get it running again i'd have to get it jump started, then it would run fine.

It's died 3 times already, the past 2 times have been when i've just been on idle but one time it just completely turned off while in the middle of driving.

What could be the problem? any suggestions?

thanks

Edited by tehbebe
Link to comment
https://www.sau.com.au/forums/topic/339974-r33-gtst-cuts-off/
Share on other sites

just remembered as well, when i turned the A/C on (While i was idling), the revs would start fluctuating, would that still be the AAC valve?

and thanks for the link ill check it out :(

i had a stuffed air con compressor and when the car was idling the revs would continuously hunt up and down from 1000 to 500 with the air con on. Air con off it was totally fine. Scrapped the air con compressor, bought a second hand one and runs like a dream now.

This fixed my problem, but sounds like yours cutting out might be more than just this.

  • 2 months later...

my idling is fine now, no problem in fluctuation in revs, but brings me to another problem, after my car has been driven hard, or given instant high revs, or pretty much when it starts to get warm, it just dies on me. If i go to start it back up, it just clicks, it wont start up on me again, eventually if you keep trying to start it up it will eventually die and you wont be able to start it up again unless i get jump leads... but here's the thing, if you pop the hood, let it cool down for about 20 minutes, it'll start up again no problem.

ANY ideas?

if it just clicks it usually means your starter is stuffed. not sure y it wove stop your car tho. does it try and turn ova when you turn the key or does it just tick. sorry bout the last post didn't read yours properly.

  • 2 weeks later...

it still clicks when it dies out but eventually if you keep cranking it, it won't even click at all.. although if i let it cool down on the spot without trying to start it up, eventually it'll start again fine. it only seems to just die on me in hot weather or once ive really 'driven' it. :(

Check simple things like your battery, your earth etc.

Could be a dodgy earth somewhere. Heat creates more resistance

Or could be a couple issues, check cas and afm (check the wiring to the plug as well)

+1

Sounds a bit like an earth problem as the symptoms come and go and affect hot-starting and make it cut out.

Could also be your alternator... Got a volts gauge or one you can hook up? If your getting a flat battery while driving (which seems to be what your describing), it'll cause these symptoms...

it definitely sounds like a battery/alternator issue to me as well. this doesnt mean that either are stuffed, you just need to check your terminals properly.

first thing i'd try is a separate earth from the alternator housing to the chassis and see where that gets you. try use a thick earth wire for this. then try the earth on the battery. if thats no good then get someone who knows how to use a multimeter to test your alternator and battery.

it definitely sounds like a battery/alternator issue to me as well. this doesnt mean that either are stuffed, you just need to check your terminals properly.

first thing i'd try is a separate earth from the alternator housing to the chassis and see where that gets you. try use a thick earth wire for this. then try the earth on the battery. if thats no good then get someone who knows how to use a multimeter to test your alternator and battery.

+1

You'll need to check them while the car is breaking down/driving/under load though, as if it sits and idles ok most of the time then testing the alternator then might not tell you anything...

thanks guys, for the updates... the battery and starter/alternator is one of the first things i checked out aswell since thats what i thought it was in the beginning, some guy checked them with some stick thingy lol and said they were fine and it was "charging properly" then he was like "i dont know much about jap cars, take it to some jap place" so i was like okay cool..... lol

i changed my AFM, cleaned AAC, changed fuel pump and fuel filter.. now i was hitting constant boost while driving home one day and it cut out again, this time cos i was on a main road and by myself i just left hazards on while waiting for a lift to help me out cos usually like i said, if i let it cool down for a good 20 mins - sometimes an hour i can start it up again.. but this time it just completely died on me, so the hazard lights eventually let my car to die, some random came and jump started me and i was able to get home fine.

i can drive the car fine, as long as i dont hit constant boost other wise it will cut out. im gonna try look into buying another alternator and see how that goes, if all else fails, ill try a new battery, umm im gonna also unblock my BOV and just put a proper gasket with a hole in it instead of the plate i have. just a thought.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...