Jump to content
SAU Community

Recommended Posts

I was wondering if anyone knows of any ECU repairers in Perth? Specifically for R33 RB25DET Power FC.

I am told my VCT isnt working and this has been traced back to the ECU not switching it on.

Anyone have any similiar experiences or advice?

Link to comment
https://www.sau.com.au/forums/topic/340113-ecu-repairer-wanted/
Share on other sites

Alternately you can use this to switch the VCT if you can't get the PowerFC repaired.

http://www.msdignition.com/Products/RPM/Ti...dow_Switch.aspx

Personally I'd double check the VCT solenoid by wiring directly to it, to mkae sure that the ECU is actually the issue.

Contact Sean automotive service solutions.

92049888

they fixed one of my powerfc's for me, but has to be sent over east..

Thanks for that. If you dont mind telling me, what was fixed and how much did it cost?

Alternately you can use this to switch the VCT if you can't get the PowerFC repaired.

http://www.msdignition.com/Products/RPM/Ti...dow_Switch.aspx

Personally I'd double check the VCT solenoid by wiring directly to it, to mkae sure that the ECU is actually the issue.

Yeah my mechanic tried 'hardwiring' the solenoid and it switched on straight away. The wiring was fine, but the actual ecu pinout is not turning on the ecu.

That looks pretty awesome! Do you know anybody who has used it on an RB25DET? VCT operates from 1800-4700rpm so I'm told so it would just switch on then, and switch off at 4700 right?

That may end up being the cheaper option, getting my ecu repaired apparently can cost up to $400.

Edited by SoFreshSoClean
Thanks for that. If you dont mind telling me, what was fixed and how much did it cost?

Yeah my mechanic tried 'hardwiring' the solenoid and it switched on straight away. The wiring was fine, but the actual ecu pinout is not turning on the ecu.

That looks pretty awesome! Do you know anybody who has used it on an RB25DET? VCT operates from 1800-4700rpm so I'm told so it would just switch on then, and switch off at 4700 right?

That may end up being the cheaper option, getting my ecu repaired apparently can cost up to $400.

Yeah, I have it in my car :down:

We setup the switch whilst it's on the dyno, so you can optimise the on/off rpm settings, as it is dependant on alot of factors like cams, headwork etc.

Yeah, I have it in my car :down:

We setup the switch whilst it's on the dyno, so you can optimise the on/off rpm settings, as it is dependant on alot of factors like cams, headwork etc.

Yeah I have standard cams/head, just bolt ons and a GT-RS turbo.

My last question is, do you have to change the on-off points for deceleration? Or is it exactly the same?

Yeah I have standard cams/head, just bolt ons and a GT-RS turbo.

My last question is, do you have to change the on-off points for deceleration? Or is it exactly the same?

No worries, the default setpoint would be fine as a starting point. The on-off points are the same for acceleration as deceleration.

No worries, the default setpoint would be fine as a starting point. The on-off points are the same for acceleration as deceleration.

Sweet, thanks for your help mate! :)

Edit: Now I'm not so sure.. I went out and opened the bonnet, as soon as I touch the throttle I can hear a decently loud 'tick'. Isnt that the VCT switching on and off?

Furthermore, shouldnt the car drive like ass if it wasnt working? :(

Edited by SoFreshSoClean
Sweet, thanks for your help mate! :)

Edit: Now I'm not so sure.. I went out and opened the bonnet, as soon as I touch the throttle I can hear a decently loud 'tick'. Isnt that the VCT switching on and off?

Furthermore, shouldnt the car drive like ass if it wasnt working? :(

having driven and work on an r33 with no vct and similar turbo (hks gt2835 pros), i can tell you if the VCT isn't kicking in the car will have no pull or power under 5000rpm. as paul mention very easy to pick on the dyno

Edit: Now I'm not so sure.. I went out and opened the bonnet, as soon as I touch the throttle I can hear a decently loud 'tick'. Isnt that the VCT switching on and off?

yep, it activates the moment you touch the throttle from idle. with a power fc anyway, not sure bout the standard computers

having driven and work on an r33 with no vct and similar turbo (hks gt2835 pros), i can tell you if the VCT isn't kicking in the car will have no pull or power under 5000rpm. as paul mention very easy to pick on the dyno

This is my dyno graph, my tuner remarked that it seems to be responding a bit like an RB26, the car doesnt have the 'punch' that you'd expect a tuned RB25 to have. I swear it has less power down low than my old standard ECU car with a catback exhaust.

As you can see the turbo is making full boost by well over 3000rpm which is a bit laggier than I expected..

post-24834-1286887201_thumb.jpg

Any ideas? :blush:

This is my dyno graph, my tuner remarked that it seems to be responding a bit like an RB26, the car doesnt have the 'punch' that you'd expect a tuned RB25 to have. I swear it has less power down low than my old standard ECU car with a catback exhaust.

As you can see the turbo is making full boost by well over 3000rpm which is a bit laggier than I expected..

post-24834-1286887201_thumb.jpg

Any ideas? :banana:

that looks normal for a gt-rs, most people make between 300-350rwhp @ 16psi. however it does look laggy. i was making full boost by 3300rpm with my hks gt2835 pros which is a larger turbo.

what size is your exhaust?

Greddy Profec Bspec 2

Have tried disconnecting it, didnt make any difference.

looks like it could use a bit more gain. theres a guide on here for tuning profecs if you wanna try make full boost earlier

The dyno graph doesn't look bad to me, I'd have expected some big flatspots if the VCT wasn't working. I'd do back to back run with the VCT plug connected and disconnected.

Maybe I am being lied to which is upsetting considering the size of the workshop :D

that looks normal for a gt-rs, most people make between 300-350rwhp @ 16psi. however it does look laggy. i was making full boost by 3300rpm with my hks gt2835 pros which is a larger turbo.

what size is your exhaust?

Its a 3-inch turbo back.. Could a blocked cat affect this?

looks like it could use a bit more gain. theres a guide on here for tuning profecs if you wanna try make full boost earlier

I was told gain is pumped right up, but then again I was told VCT isn't working.

Maybe I am being lied to which is upsetting considering the size of the workshop :D

Its a 3-inch turbo back.. Could a blocked cat affect this?

I was told gain is pumped right up, but then again I was told VCT isn't working.

I would say you VCT is working.

We replace a broken VCT and with the broken one when you open the throttle on idle you can't hear anything but with a working one there is a very noticeable click.

The car was an r33 with a hks 2835 pros with no VCT it was a dog low down, once it hit 4000-5000rpm it just pick up aheap of power and was very untuneable due to the huge change in such a small rev range.

so my guess is your VCT is working, best way is to just unplug it take it for a drive, see how it drives, plug it back in and see if it is any different.

And yes a block cat wouldn't help the flow out of the exhaust so could possible be that, BUT i really thinking there is nothing wrong for the amount of boost you are running.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That is surely the biggest gathering of Stageas in North America, ever!
    • Remember kids - if you can't afford to buy 2 GTRs......
    • I know people cry at the price of the Getrag 12-14k for a conversion now, but it really is a nice mid point. Not going to get change from 10k on a gearset installed.  $30k++ for sequential.   I know you run the risk of a damaged used one and parts are hard to get but as a street car gearbox its really hard to beat. If you enjoy a more traditional manual, its the choice no question.     
    • Time to decide what’s more import, your power level or your budget because you’re going to struggle to keep both 
    • Our Southern Highlands Cruise is proudly registered with “R U OK?” Day.  Sometimes the best way to check in on your mates is by getting out for a drive together. Sharing a common passion like cars creates the perfect space to chat, connect, and support each other.  A simple “R U OK?” can make all the difference. Let's enjoy the drive, the company, and look out for one another. PLEASE WEAR YELLOW FOR “R U OK?” DAY Sunday 14th September 2025 9:30AM Meeting Crossroads Homemaker Centre 10:00AM Cruise Departure Via Old Hume Hwy 11:45AM Arrival at Mittagong RSL Club Meet Location: Crossroads Homemaker Centre Final Destination: Mittagong RSL Club *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...