Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Thats the point....I still say 23.1 in my car isnt that quick. Its two seconds off where it should be. If that 23.1 was a 21.1 then I would happy where the gun tag...but as is that times sells the car short!

I'd be happy with a 23.1 at Sandown. Still a clear sec quicker than me. Not sure where my time has gone on that track?

I carry enough speed at turn 6 kink (almost slide through there) and brake as late as possible at nearly every corner...

I think it's just drive out of the corners there that I struggle with and bouncing ripple strips may not be the best approach.

If you think that a 23.1 sells it short i'm looking forward to what comes next with your car. :) You've been right about almost everything that a rwd skyline (non-Big Red haha) is capable of on semi's so a 21 isn't out of the question.

Ok in car vids are up....

First is my new PB lap....the fist pump at the start finish line at the start of the lap was when I saw a high 47 flash up on my previous lap :)

and this is a collection of some overtaking. First part is me trying to overtake a big single turbo R34 down the straight only to be passed like I was standing still by a 6.6ltr V8 powered 260Z :) ....middle part is me catching and passing a GT3 cup car and last part is an ex(?)-V8 supercar - we came out of the last corner side by side only for him to pull away down the straight using ubber killerwasps. Two corners later his lead disppeared thanks to corner speed and I was able to overtake.

Enjoy :D

Ok in car vids are up....

First is my new PB lap....the fist pump at the start finish line at the start of the lap was when I saw a high 47 flash up on my previous lap :D

and this is a collection of some overtaking. First part is me trying to overtake a big single turbo R34 down the straight only to be passed like I was standing still by a 6.6ltr V8 powered 260Z :D ....middle part is me catching and passing a GT3 cup car and last part is an ex(?)-V8 supercar - we came out of the last corner side by side only for him to pull away down the straight using ubber killerwasps. Two corners later his lead disppeared thanks to corner speed and I was able to overtake.

Enjoy :D

Well done Ant, lookiing at those vids I can see why your doing the times you are doing, very smooth and the car looks very stable in the high speed corners, noticed your holding flat through turn 3 and hayshed, good stuff....

Not far from a 1:46 now... Keep up the good work.....

I have some vids of me doing a 1:46, let me know if you want to compare the two...

Thanks for the kind words guys. I'd say that the vids make my driving look smoother than it felt in a few places! My biggest issues on the day were pulling the car up for Honda as I had the ABS kick in a few times and balancing the power around the 2nd last corner.

Given my times on the day I'd say that the car is capable of a high 46 on a perfect lap. Even with the stocky suspension I have been taking turn 3 flat, but since the suspn upgrades the car has felt stable enough to take hayshed flat too. This stability allowed me to make gains (by seat of the pants feel anyway!) around most of the corners but in particular I'd say Southern loop and lukie heights were by the biggest margins.

I would love a copy of your 46 lap Jack as it would interesting to compare, despite our firepower differences ;) ....is it available on youtube?

Hey ant, here you go:

http://sau.ferni.net/Jacksvids/PI_31_03_07a2.wmv

Right click 'save as'.

Minimize and play them together with your YouTube vid.

I did my best to play them together from the start/finish line, but it's a bit hard as you cannot press play simultaneously.

Enjoy!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
    • Thanks, these seem to lay it out a bit differently. I will get back to you guys after i do some tests and more digging. 
×
×
  • Create New...