Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Guys this is usually attributed to the transfercase to front diff tailshaft. Pull it out and you will notice that as you turn the uni joints around manually they will be quite notchy. The other usual cause for this is the front CV joints needing the grease to be removed and repacked. But I'd be pulling the front tail shaft out first and feeling if the uni's move without any notchy spots. My bet is it will be! Seen atleast 4 like that now including my own.. replace the shaft.. all good.

OSF TRACK ROD END WORN BUT NOT SURE IF IS THE PROBLEM , WAS STARTING TO THINK ABOUT SOME SORT OF BUSH SOMEWHERE IN THE DRIVE-TRAIN MOUNTING , WILL CHANGE TRACK ROD END FRIDAY AND SEE

Caps lock off please :P

Guys this is usually attributed to the transfercase to front diff tailshaft. Pull it out and you will notice that as you turn the uni joints around manually they will be quite notchy. The other usual cause for this is the front CV joints needing the grease to be removed and repacked. But I'd be pulling the front tail shaft out first and feeling if the uni's move without any notchy spots. My bet is it will be! Seen atleast 4 like that now including my own.. replace the shaft.. all good.

can the joints be replaced or do you need to replace the whole shaft!

Welcome back to the forums mat! Hope your ready for some fishing this summer, I'm inquiring into buying a tinny tomorrow. Look out all garfish in the bay! Haha

And to ben, the shaft isnt that hard to drop out, I somehow can get a socket on one end and ring spanner on the other... Intact I can often crack them by just using the socket end sure they spin a few times before they bite and un-do but it does happen eventually. They don't need to be ball breaker tight either. Got a spare shaft you can try here to ben if your joints are suspect not sure how good the joints of my spare are but you could use it to eliminate issues :-)

I've also noticed I am starting to get this slight shuddering under hard acceleration ...happens from about 50-90 km/hr.

Also have a slight noise, much more pronounced when turning out of corners but related to heavy throttle and heavy engine load only...doesn't do it at idle or when engine is revved at idle. Kind of sounds like a wheel bearing noise but not the wheel bearings...CV's ? driveshaft uni's? accessory pulley? water pump? Related to above problem or seperate?

I call it the 'Stagea Strange Noise' (SSN) and keep driving.

Well been chasing this same vibration problem now for a couple of weeks so far replaced front cv joints, wheel alignment, then today replaced front drive shaft from transfer case (with a GTR one) coz removed old one and def felt notchy and guess what still getting vibration :) ???????? what next rear drive shaft any one had trouble with these seems to bo a cv joint in them as well as uni joints

cheers

rose

yeah new wheels on there all balanced also had two other sets on there all did it as well :)

If the problem is not sorted by the time of the Stagea cruise I'll jump in the car with you and see if I can diagnose it for you.

:)

Guys this is usually attributed to the transfercase to front diff tailshaft. Pull it out and you will notice that as you turn the uni joints around manually they will be quite notchy. The other usual cause for this is the front CV joints needing the grease to be removed and repacked. But I'd be pulling the front tail shaft out first and feeling if the uni's move without any notchy spots. My bet is it will be! Seen atleast 4 like that now including my own.. replace the shaft.. all good.

Well the bolts were effing tight and I'll end up replacing all the nuts - 2 of them got burred. But, the sucker is out, and the uni's _are_ knackered.

I'll be dropping the shaft into Adelaide Tailshaft Services ASAP to get the uni's replaced. A new shaft is $1100 (special price) from Nissan...

I test drove the car last night, and the vibration under hard throttle seems to be fixed (but the traction is certainly reduced. For those that have wondered - the ATTESA-ETS is used LOTS, even in everyday driving). However, my wife has indicated that a vibration at ~100km/h is still there. Its nature is consistent of wheel balance issue (rotation movement in the steering wheel), so I'll be getting that seen to this weekend (which is almost due anyway), but will check the CV's for play between now & then.

Really not a fan of auto gearboxes and so i dont know enough to be able to know, but is clutch shudder possible with an auto?

Edit: Didnt see the second page, seems to have been resolved lol

Guys this is usually attributed to the transfercase to front diff tailshaft. Pull it out and you will notice that as you turn the uni joints around manually they will be quite notchy. The other usual cause for this is the front CV joints needing the grease to be removed and repacked. But I'd be pulling the front tail shaft out first and feeling if the uni's move without any notchy spots. My bet is it will be! Seen atleast 4 like that now including my own.. replace the shaft.. all good.

How do u pull out your front uni, theres four bolts toward the front of the car which will detach the front end. Does the back end simply pull out, if it does is there going to be any oil/fluid come out or is it like a dry spline.

  • 1 month later...

well i still have this persistant little problem of the shudders all uni and CV joints replaced new front drive shaft in big improvments, but looks like problem has been located while having the car up on the hoist to fit auto shift kit in had a good look around and the rear drive shaft center bearing looks deteriated giving the drive shaft some play especially when the drive line has warmed up so looks like replacement time hard part is have to take it out so can take it to some one so they can match new one up unless any one on here knows part number for one. But the MV automatics shit kit is excellent best improvment yet :wub: chirps in to second

Edited by 4bidn1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...