Jump to content
SAU Community

Recommended Posts

Fully rebuild RB26 head with

Oversize ferrea valves,

Ferrea titanium retainers,

Ferrea valve springs,

Ferrea spring Locators

Ferrea valve locks

new buckets and shims,

New guides and seats.

GREDDY procams 264 duration & 9.7mm lift Part numbers 13525220 & 13525213

pics below Ive added the current cost to buy the head components below.... add machining, new buckets and shims and camshafts etc and the head owes me a shiteload... 5-odd thou built for big power and to rev 9000+rpm.

It has rear drain if you want it.

$3400ono

Newengine005.jpg

Newengine002-1.jpg

Newengine004.jpg

Newengine001.jpg

post-34927-1288591126_thumb.jpg

Hey Mate

Has it been ported etc?

What sort of power was this running?

was heading to 450rwkw but no injector duty left.

Sold pending payment

was heading to 450rwkw but no injector duty left.

Sold pending payment

Let me know if it doesnt go through

email [email protected]

Cheers

Matty

Let me know if it doesnt go through

email [email protected]

Cheers

Matty

Payment was made yesterday sorry.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...