Jump to content
SAU Community

Recommended Posts

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

seriously HAD to get some decent pads before Tuesday (Morgan Park) though, coz the current ones are getting pretty low and some of the braking last night was a bit scary

Hey....do you think I should do the rears at the same time?

a bit worried about the bedding in procedure though

I can't drive 200m around here without hitting a set of lights, and you're supposed to do like a couple of 60 -20 stops and then a couple of 100 - 0 stops to bed them in.

Maybe I should just put them in at the track and do the bedding in there.....what you think?

oh u mean onbail and 20wn u

yer i didnt think much of that, i suspect its anna32's "crew" and they dont think much of us?

yeah that's them.....well if they don't think much of us.....THEN DON'T COME ON OUR CRUISES.......fu(kin up themselves wankers if you ask me

Wawrick, I think stop being a pansy and just bed them in :devilfu:

thanks Matt...lol

I'd prefer to follow the correct procedure than do it half assed and not get the best performance outa them......

your supposed to drive for like 10 - 15 mins after the braking runs and not brake at all....HTF are you supposed to do that unless you do the pad change on the M1 or something?:D

hey matt

um just get out on the m1 and go for a drive, cause ur sposed to hit em hard a few times 100-70 or something like that then not touch em for 15 mins so they cool properly ie just drive round so they cool down

yeah....but the M1 is like 50 ks from my house....there's gonna be a lotta braking done before I get there

btw....I have nothing against anna32...at least she gets on the forum and actually talks to people....but to turn up to a cruise having bever posted on here and then act all aloof, ummmm.....excuse me, but .....FU(K OFF!!!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...