Jump to content
SAU Community

Recommended Posts

Well you rock up to a test, they see a 3.5"/4" outlet - you think they aint gonna suspect something is up? :devil:

I had the guy get under my car when my 3.5" exhaust pulled as low as it did, just to check for that type of thing.

I had one on my old R33, the difference was amazing. From a headache inducing drone to quieter than my friend's Excel. The benefit is not that it will pass an EPA, its that whenever you see cops, get pulled over, or simply don't want to annoy the neighbours you can mute it instantly from a button on your keyring. It prevents you getting EPAs in the first place, rather than assist you in passing them.

I was so impressed with it I bought another for the Supra, but never wired it up as my current exhaust set up isn't that loud in the low revs.

I've got one and the only reason i got it was i cbf with headaches sometimes from my exhaust /drone as said above by Kez but also i have very good neighbours who all respect each other and id like to be quiet when i come home numerous times in the early morning with my car.. :banana:

EPA's are less of a headache as u get pulled over and they check to see if ur cars loud and they notice its dead quiet. just gives you less headache.

This video here is my old car, and a video I filmed and uploaded personally. Who knew it would hit 170,000 views. I doubt the valve would cause much of a restriction unless you were already pushing the limits with your exhaust diameter.

As for the noise, I reckon the sound fine. I've had a ton of complements on my Supra's exhaust note and it has a Varex. IMO its everything before the muffler that gives an exhaust a nice note or not, depending on your turbo/extractors, mid mufflers, cat, resonator, pipe size, material etc. You can also get different muffler shapes and tips too, next time I think I'll just get the twin tip for an even more stealth appearance.

I know I sound like a bloody Varex salesmen, but to be honest they really are that good. Well worth the money and the main reason it was the first mod I bought for my Supra.

They're great at what they do, you don't buy it to have the best sounding exhaust, you buy it to have the best of both worlds. Personally, I love the note, it's deep down low and up top is a real screamer. I think it's important that the rest of the exhaust is done properly or it will sound tinny and crap, but that's like any exhaust. Run 3 inch mandrel mild steel from the turbo back and you'll be sweet...come listen if you like.

This video here is my old car, and a video I filmed and uploaded personally. Who knew it would hit 170,000 views. I doubt the valve would cause much of a restriction unless you were already pushing the limits with your exhaust diameter.

As for the noise, I reckon the sound fine. I've had a ton of complements on my Supra's exhaust note and it has a Varex. IMO its everything before the muffler that gives an exhaust a nice note or not, depending on your turbo/extractors, mid mufflers, cat, resonator, pipe size, material etc. You can also get different muffler shapes and tips too, next time I think I'll just get the twin tip for an even more stealth appearance.

I know I sound like a bloody Varex salesmen, but to be honest they really are that good. Well worth the money and the main reason it was the first mod I bought for my Supra.

If all the varex mufflers are like that its not worth it since its got a restrictor welded in there thats why the hole is so small. I just removed one out of my cannon. So even when its fully open you still got a restrictor there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...