Jump to content
SAU Community

Recommended Posts

I've done many many many jump starts with my PowerFCs and had no problems.

This is how I jump start cars:

1. Back cars up together

2. Connect cables

3. Start the car with the good battery

4. Leave for 5-10 minutes to trickle charge the battery in the flat car.

5. Start up the flat car, and immediately disconnect the jumper leads

6. Switch off the good car.

7. Go drive the flat car.

No problems with frying my PowerFC.

Tony,

Don't forget that I am purely speculating about my problems - It might not have been the charging at all.

PH1 had seen simlar issues where the PFC lost it's AFM settings - (I have Q45 so maybe not many ppl have set this way)

If anyone wants to try my PFC in their car, gimme a hoy - I'd be interested to see if it does the same thing ( ie not start ).

Damn cars - such a waste of money....... :P

I have had to jump start my car with PFC installed a few times now and had no dramas.

I beleive the most potential damage is to the car doing the jump starting.

Either way I have used an earth on the chassis of my car for the 'ground' and simply clipped the positive clamp onto the + connector under that cover on the drivers side under the bonnet.

Clutch starting has gotta be much safer for the electrics doesnt it?

Adrian

Hmmm interesting - I wonder if that is all that is wrong with mine.....

Damn sewid - that must suck , having to re-program every time you loose power - Especially if you hadn't taken a note of the old settings - then you would need a re-tune.

Yeah luckily it hasnt been an issue yet because everytime i pull the power all i lose is the "boost controller" setting since im using the base map.

For now im running the stock ECU though since on the base map the knock detection goes over 80 sometimes (only did it once but took it off after that).

Ill open it up to see if there is a replaceable power cell.

I've already done that on mine - there is no battery in there - settings must be stored on NVRAM.

So do all your settings revert back to base map ?? ie if you change any timing or fuel settings, they also get reset ????

I reckon we should be able to find an electronics guru who could fix these things.....

Guest RedLineGTR

well i havent had my stock ecu fry so i dont think the power fc would be any different its still a ecu and but i just remembers more settings. Apexi would of mentioned it if they had a problem with it ;) read the manual of the power fc (english) and my mate read the jap version no mention of it. Havent heard of anyone with a problem like this. My 2 Cents :D

I don't think you can say that - the PFC might have different electronic components and different power supply components and different voltage protection, etc.

They are two completely different ECUs. Designed and built differently.

Either may or may not be suseptable to spikes or surges.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...