Jump to content
SAU Community

Recommended Posts

Thanks for the quick response guys.

I'm not miffed that the car doesn't come with brembos as I got it cheap and it can be rectified, I'd just like to know for sure as to why.

Take for example this thread where someone mentioned V-Specs being equipped with brembos while standard R33 GTRs did not come with brembos.

QUOTE

Vspec has active LSD (a yellow light in the dash)

Vpsec has the faster attesa computer 1/1000th of a second rather than 1/100th (not visually noticable)

Vspec has stiffer suspension stock 10mm lower (not visably noticable)

brembos

10kg more weight (not visably noticable)

A Vspec sticker

Air difusers for the front brakes

Slightly better ABS (not visually noticable)

Finned rear diff

Edited by Jebat

Tomek doesn't actually say that non vspecs didnt have brembos, just that vspecs did. easy way to solve your question is to get your chassis/vin number and run it through Nissan FAST. it a program that'll tell you what spec of car the vin matches, with all the options that were included etc

Tomek doesn't actually say that non vspecs didnt have brembos, just that vspecs did. easy way to solve your question is to get your chassis/vin number and run it through Nissan FAST. it a program that'll tell you what spec of car the vin matches, with all the options that were included etc

Thanks for the suggestion Basti: jonboy did that for me on the 22nd of October and it is a GTR:

http://www.skylinesaustralia.com/forums/in...t&p=5510286

post-a310297-BCNR33-023728.jpg

So is it safe to assume that before the R33 GTR was shipped out of Japan, someone swapped out the Brembos? Since everyone is of the opinion that even early BCNR33s, were never equipped with Sumitomo calipers?

Edited by Jebat

Yep someone did a fast one on it... Just look for a set of brembo's.

Vspec R32GTRs came with brembos so there is no chance that they wouldn't of had the brembo brakes ready for the R33's.

Wouldnt surprise me if a previous owner had upgraded from brembos and sold the brembos to fund some money back.. then removed the new brakes when selling and just bought cheap ones to sell car off..

Oh that really sux ;)

Now I doubt my brakes are brembos because all over the net all the r33 gtrs have 'brembo' written on it.

F&*CK.

How am I supposed to know what brakes I have then... I bought a full set of brembo brake pads too fck.

Ok I can confirm I have sumitomos.

Are these standard on '95 r33 gtr NON-vspec or have I been fleeced?

http://en.wikipedia.org/wiki/Nissan_Skyline

Scroll down 75% to R33 > GT-R brakes (v-spec or non)

Wiki isn't always correct, but in this case, I think it is.

I thought this is known to 90% of us... All 33 GTR variants came with brembos and so did the 34s. Its only the 32 that doesnt come with them (from memory 32 vspec2 does come with them and maybe vspec too?)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...