Jump to content
SAU Community

Recommended Posts

yep very impressive

read a review where they say the extra 40hp feels like 100, and theyre probably right

ill look into swapping my '10 for an '11 when it hits the showrooms

ill have around 10k kms on it by then

Really? I would just get a tune on an 09 or above. it will feel faster than the new one easily.

Link to comment
https://www.sau.com.au/forums/topic/344311-new-gtr-2011/#findComment-5550789
Share on other sites

Really? I would just get a tune on an 09 or above. it will feel faster than the new one easily.

as much as i want to, and would have already done so by now, i like being held tight at night with a manufacturer warranty

ive been down the void warranty route in modifying my M3 and it was no fun when things (inevitiably) go wrong

it will be a drainer to have to repaint/clear bra the sills, re-dynamat the rear seats, and swap over a few other bolts on, so ill drive it when its available and see if it's worth the hassle

quick note on that vid, seems theres no axle tramp when using the LC like all the series 1 LC vids

what i really want to know is if they've gotten rid of that 0.5 seconds of no-mans land jumping on the throttle from standstill

Edited by domino_z
Link to comment
https://www.sau.com.au/forums/topic/344311-new-gtr-2011/#findComment-5550802
Share on other sites

It really appears that all the difference besides the extra 40 HP (which would account for all of maybe 0.2 second) is in that initial jump. Other than fine tuning the launch RPM what else could they have done? It would be interesting to observe the boost gauge on the new model to see if they have managed to get the turbos spooling up more with foot on brake and accelerator so that more torque is available instantaneously and more smoothly at lower RPM without the monstrous RPM shocking the drivetrain as was the case with LC1. Has anyone played with the new Cobb Accessport with the TCM module and launched at the preset 3300 or 3700 and seen what difference that makes to 0-100 times?

Very impressive nonetheless. I wonder if the quarter mile has improved significantly?

Edited by fungoolie
Link to comment
https://www.sau.com.au/forums/topic/344311-new-gtr-2011/#findComment-5551327
Share on other sites

Very impressive nonetheless.

Yeah i agree. On it's own - compared to common mods most of us do (exhaust, tune, e85, etc) it's nothing specia really, but as a full weight STOCKER car (a fraction of the cost of comparable vehicles) if they are running 0~100km.hr in 3.04s then that is seriously impressive.

Link to comment
https://www.sau.com.au/forums/topic/344311-new-gtr-2011/#findComment-5551445
Share on other sites

as much as i want to, and would have already done so by now, i like being held tight at night with a manufacturer warranty

ive been down the void warranty route in modifying my M3 and it was no fun when things (inevitiably) go wrong

Yes but Domino that would be a false economy spending all that cash just to for the sake of maintaining your warranty and be doing sub 3's. You'd be dropping $40K by selling your current car and then having to spend another $20-$30K extra (if the rumours are correct) on the new one. You'd probably be able to buy the AMS or Switzer 1000HP packages for that kind of money and have some left over for the "inevitable" breakages.

However to be more sensible I'd go down the Cobb, Midpipe, E85 route and get Martin to upgrade the trans to take the extra grunt if you're really concerned. Warrranty is worth something but not that much!

Edited by fungoolie
Link to comment
https://www.sau.com.au/forums/topic/344311-new-gtr-2011/#findComment-5551510
Share on other sites

the change over wont be a deciding factor

will wait to see how/if it drives any different

as much as i love this car, there are less tangible things i value in the new model - the uprated interior materials, improved paint quality, etc that i will wait to assess in the flesh

Edited by domino_z
Link to comment
https://www.sau.com.au/forums/topic/344311-new-gtr-2011/#findComment-5551574
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...