Jump to content
SAU Community

Recommended Posts

So its pretty much stock S2 stagea with blitz air filter and exhaust with sbc i colour, i have a little box in the passenger footwell with SIDC box???

it has a mines ecu with :

Fuel mapping has been changed

Ignition timing adjusted

Speed limiter cut

Rev limiter raised plus(+) 300rpm

Guys at autoworx recomending i get a new fuel pump.

I want to get a new ecu as it is.

here is dyno sheet, i believe this is on mid level boost....

S50C-110111615350.jpg

Link to comment
https://www.sau.com.au/forums/topic/344518-just-had-my-car-dynod/
Share on other sites

Nope.

It is kind of like a piggy back but is sort of like a completely new ECU. It is additional 'address space' and kind of interrupts the factory default values and is placed inside the factory ECU.

This basically allows you to have full adjustment of pretty much everything via the consult port via some cheap laptop software downloaded from the nistune website. For example, I can now change the Thermo fan set point which was usually an 'emergency thermo' for my SR20DET. I've removed the factory clutch fan and now the ECU takes care of cooling duties!

hay man that mines ecu you have the best thing to do with it is to remove it and throw it in the bin !!!!! my mate had one in his 33 and it caused all kinds of problems for him and never tuned properly , and would always lean out on a high boost setting and could never hold a smooth AFR for some unknown reason . seriously man the best thing to to is to spend the 400 bucks on a nistune daughter board installed into a STD ecu and all your problems will be solved . my s2 before i installed the nistune was pulling 235 hp on 10 psi , and 2.5 exhaust std cooler and turbo smart boost tee . now i have a 3'' exhaust , FMIC and coustom intake setup , but i havent had it tuned yet because of getting hit in the ass by a stupid ford driver and having to get it fixed but now i have it back so it should be all go after christmas , and im hoping for around 290 -320 hp at all fours with a goog tuner . cheers spinner ..

How much are they normally
See if this one's still for sale - I think he wanted $400 for the ecu c/w nistune chip - you could just plug it in an get a tune.

http://www.skylinesaustralia.com/forums/Ni...fm-t340680.html

See if this one's still for sale - I think he wanted $400 for the ecu c/w nistune chip - you could just plug it in an get a tune.

http://www.skylinesaustralia.com/forums/Ni...fm-t340680.html

+1

$450 I recall for the ECU.

Thats if its still available. The thread was killed by some non-buyers tearing at it.

The board itself is about $280, a single user license for the NIStune software is $200 I think (you don't need this, it's only if you want to be able to fiddle with stuff yourself, or ask me to do it :) ) - both purchased straight from NIStune.

Carton of beer to a competent electronics technician to install the board.

Then find your tuner of choice (I can recommend Hyperdrive and Allstar Garage) and pay by the hour for tuning. Shouldn't take too long as it's pretty much stock.

Edited by bubba

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...