Jump to content
SAU Community

Recommended Posts

would change AFRs aka just dump in more fuel making the car richer.

that's that i would guess for $12.

Exactly. Tricks the car into thinking it's colder, therefore dumping more fuel into the engine. Will it work? Marginally. Is it terrible for your engine? Well...

Link to comment
https://www.sau.com.au/forums/topic/344550-what-is-this/#findComment-5553410
Share on other sites

It changes the signal for the coolant temp sensor not the air temp.

But yeah...cant see it doing anything other than washing all the oil off the bores and ass raping your engine with a pineapple attached to a jousting stick.

Link to comment
https://www.sau.com.au/forums/topic/344550-what-is-this/#findComment-5553795
Share on other sites

It will modify any standard ECU by telling the ECU that the incoming air in the intake system is cold

description makes it sound like it's for a air intake temp sensor.

you could essentially just unplug your coolant temp sensor though. will have the same effect. the thing is though, on long trips it may really affect fuel economy if the resisitor in the little box (that's all they are) made the ecu think the engine temp was so low that it ignored the o2 sensor and just ran on the cold start enrichment maps.

Link to comment
https://www.sau.com.au/forums/topic/344550-what-is-this/#findComment-5554012
Share on other sites

also won't work on rb20 or rb25 powered cars as they don't have an intake air temp sensor.

i'd also like to know how adding in more fuel (which they say happens in the explanation) equals better fuel economy, lol

I knocked my temp sensor off one day to the ECU, car wasn't too happy about it once warmed up.

Link to comment
https://www.sau.com.au/forums/topic/344550-what-is-this/#findComment-5554024
Share on other sites

It could and has worked before.. you just gotta know what it actually tries to do so you don't expect too much.

Generally these resistor/chip/box mods will tap into the coolant temp sensor and lower/raise the resistance value fed into the ecu (depending on the type of sensor you have - some go higher when hotter whereas some go lower when hotter), then once the ecu picks up that the car is supposedly running in a cool environment, it will advance the ignition timing to suit equaling more power.

The main thing it depends on is your OEM ecu having ignition timing advance for colder situations - if the ecu has that and you install this crap correctly, then it will work to an extent.. much like driving some bog stock normal car in 10degree night weather vs a hot summer day (taking into account the air is less o2 rich during your testing the device vs driving during a really cold night and also heatsoak).

You can potentially save fuel by having to be on the gas a little less going up hills or maintaining speed etc as your car will have slightly more torque so you do not need to depress the throttle as much as before the 'mod'.

Long as you have basic electronics understanding, how car systems/ecu works etc, you can do this for a couple of bucks (buy a pot to see which resistance value gives best results then buy a simple resistor in that value).

While it may seem like i'm giving this a good rep.. nope not at all (not saying it won't work either because done right it will as long as your ecu has timing advance for colder running situations, a coolant temp sensor and a conservative factory tune). But it's sometimes nice to know the theory behind things.

Link to comment
https://www.sau.com.au/forums/topic/344550-what-is-this/#findComment-5563746
Share on other sites

most ecu's add more fuel when cold, as well as possibly adding more timing, so when at full throttle you will use more fuel, and when cruising you may simply use the same amount of fuel. all in all though, you would normally see worse fuel economy with something like this. i've had cars with dodgy thermostats making the car run cooler and fuel economy was better once the thermostat was replaced.

Link to comment
https://www.sau.com.au/forums/topic/344550-what-is-this/#findComment-5563937
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...