Jump to content
SAU Community

Recommended Posts

  • Replies 113
  • Created
  • Last Reply

Top Posters In This Topic

well done! yeah I have tried and failed to flare one before. it's not easy but I can see it could be made to work. solid lines are the best way for as much length as you can use them for so it's a good idea. they are not porous so no smell and much cheaper than running meters of telfon line with stainless braid.

diff mount looks interesting too.

Cause it's a shitter 31 :)

jks nick

31 diff housing is a lot stronger than later model shortnose housings :P

gonna look into using hicas lines soon, probs gonna need twin 044s for e85 or e42.5. anyone tried simply putting some welds onto the end of the hicas lines and then clamping a hose onto it? like with cooler pipes

^^ in regards to the % duty on 1000's I sailed past 50 % duty of my ID 2000's VERY early on into the tuning process.... I didnt take much notice of what the Duty was at the end of it but personally I would be putting in the 2000's in.

What fuel pressure did you end up running...?

  • 3 weeks later...

They are a pain in the arse to flare but it can be done - there's no way you will get a proper double flare on them though.

diffmountfitted.jpg

nice setup - i wonder if there is the same clearance on the r32gtr between the diff & tank?

For anyone searching in the future, recently a GTR managed 707awkw through twin 044's on E85. Thanks NYTSKY for the headsup!!!

the boys @ powertune also had a similar result & making over 600awkw or 700awkw

I've got x2 044 w/ tomei lift pump and I'm buying some 14mm id2000's.

RB30 + new EFR8374 + E85 should be an interesting combo.

Snap....Almost exactly the same as me, I have a Nismo lifter and ID1000's (Which will prob be too small for E85)

Have you got your EFR yet? I'm still waiting for mine, I have the .92a/f T4 internal W/G one coming.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...