Jump to content
SAU Community

Recommended Posts

Hi,

I've got a R32 gtst and my front coilovers are ont he way out and I'm about to buy some new ones.

I was wondering how bad softer spring rates on the front would be?

Right now I have 8kg rates int he back and the coilovers I want for the front are 6 or 7kg's.

Is this a terrible idea? It would be mainly for street driving and drifting once a month.

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/345610-higher-rear-spring-rates-bad/
Share on other sites

  • 2 weeks later...

not terrible, but unwise, depending on your ARB rates, and at a long shot, ur RC heights.

inducing huge oversteer doesnt really help anything, circuit it just makes the car shit to drive, auto/motokhana it makes the car shit to launch, and drift it makes the car lack any ability to hold high angle (although making it easy to an amateur to initiate)

I dont think the differences will be massivly drastic.

And its not a bad idea.

You may have to adjust the way you drive a little and prepare to catch the car when your giving it a poke.

Softer springs in the front will increase complience in the front and decrease understeer, making it want to oversteer.

You can tune out some of the oversteer if your THAT worried about it by running 1-2mm of toe in on each wheel at the rear and getting the camber settings right at the rear. Also, you can run lower tyre pressures in the rear. If you can, soften the dampers at the rear and soften swaybar if you can adjust it.

well soft springs...say king springs will make the car comfortable but handle like shit as you do want some amount of hardness. the usual spring rate is 8 front 6rear for s13 sr/ca but for a r32/a31/s13 with a rb in it 10 front 6 rear

Edited by Dan_J

6 or 7kg front and 8kg rear will be nasty to drive and you'd really want to be on-the-ball if it ever rained. Trust me. I actually play around with different spring rates on my track car, not just make a guess and say "I doubt it will be a big deal". Even 25lb/in increments (half a kg/mm) make big differences.

"Softening shocks" will not change the mid corner balance, that's all down to spring rate. Shocks affect transient behaviours - change of directions, bumps etc.

The sensible thing to do is put the current 8kg rear springs on the front coilovers, get the 6kg springs with the new coilovers and fit them on the rears. 7kg would still be taily with 8kg fronts.

What's the current front spring rate?

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...