Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

I reckon your head requires a bleed mate. This is what happens when boys buy stageas. lol

heh Stinky ill stick commodore pursuit rims on it and put in half a king spring - for that ulehness. :banana:

yeah yeah.. as i said i wasnt driving.

and i drive quite safely tyvm

anyway as goldzilla said.. no excuses

Edited by PetroDola
Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5572859
Share on other sites

hehe should i be scared you actually know this dale ? :banana:

The amount of useless information I've collected, you would not believe...

Case in point; the active collection of useless information is known as "Spermology"

Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5572906
Share on other sites

Im not against skids, I have done many. My only issues are 1. If you need to use the brake to do a skid go buy more bolt ons(yes I realize that's what your doing) 2. Skid vids on forum = poo

Might I add:

3. DON'T do it on a public road, no matter where it is!

Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5574383
Share on other sites

lilcrash if you cant brake boost .. you evidently dont know how to drive.. and secondly .. let me see you control a doughie in barely 2 lanes in 2nd gear. and keep it on the road. again.. this is rich coming from someone who was promoting getting an insurance job on his car to save money...

and PM MAD - youre the only volvo driver you idiot.. youve got a non turbo rx... so shut the f**k up you douchebag.

so many haters ... seriously go get f**ked hey.. i dont give a f**k about your shitfulll attitude.

Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5574634
Share on other sites

lilcrash if you cant brake boost .. you evidently dont know how to drive.. and secondly .. let me see you control a doughie in barely 2 lanes in 2nd gear. and keep it on the road. again.. this is rich coming from someone who was promoting getting an insurance job on his car to save money...

and PM MAD - youre the only volvo driver you idiot.. youve got a non turbo rx... so shut the f**k up you douchebag.

so many haters ... seriously go get f**ked hey.. i dont give a f**k about your shitfulll attitude.

lol f**kwit from perth hills.. go back to armadale you rednecked wanker.. lol

hmm.... reads like someone other than Kier is using Kier's account

Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5574672
Share on other sites

yeah i posted a video in bad judgement.. least goldzilla and others had the balls to give reasons why this was frowned upon without letting their self inflated ego's get in the way..

nah just over copping shit iamhe.. theres no need for it.. i accept i made a mistake. but i think others taking it too far.

if they wanna delete me for it... i dont give a shit. im over it.

if they want to stand around like a bunch of f**king children stomping their feet in a circle like an elephant cheerleading squad thats their perrogative. but i didnt come here for that childish bullshit.. so i dont really give a shit as you can see.

Edited by PetroDola
Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5574674
Share on other sites

bad judgment is exactly it, but now you're coming across as immature.

if you post something on a public forum, you should be ready for any reaction (whether good or bad)

it just appears you are getting angry now because you didn't get the reaction you were hoping for...

live and learn, not the end of the world :blink:

Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5574738
Share on other sites

there is no point getting angry at me, i never said i couldnt brake boost, i said that only pussy's use the brake to skid and if your car hasnt got the power to skid buy more bolt ons. mayb you read that wrong. i understand that r33 = poo and cant skid. just accept that your "friend" and your car cant skid and let it be. 1. you shouldnt be doing "doughies" on the street thus not having gutters to hit 2. you shouldnt make video evidence of your car doing skids 3. you shouldnt post said video evidence on a forum where someone on the other side of the law can find it and use it against you not to mention get you flamed for doing said "doughies" on a public road. 4. i didnt post a video of my car being stolen and the engine being buried in a big hole on a forum.

i accept that you have admitted bad judgement and thats why i will stop my rant.

good luck with the engine build. laterdays

Edited by lilcrash
Link to comment
https://www.sau.com.au/forums/topic/345801-skyrice/page/2/#findComment-5574763
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...