Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

UM let me guess.......................STOCK AS A ROCK!!!!!!!

If you had mods and posted 153rwkw from a car that has 190 odd flywheel kw factory spec, wouldn't you be :Oops:

Thats my guess!

That's a pretty good power output then when you can consider the following:

* Full 3" Turbo Exhaust = 10-15rwkw

* Ex Cam Gear = 10-15rwkw

* FMIC = 10-15rwkw

Their's a potential 30-50rwkw just from another $3,000.

I got 160.6rwkw from AVO with known mods pod, clutch.. though a/m boost guage was showing ~10psi top end but still using the factory solenoid so there might be more mods than that (as factory solenoid is supposedly to be 5->7)

Exhaust looks stock as far as I can tell too.

dyno graph

I got 160.6rwkw from AVO with known mods pod, clutch.. though a/m boost guage was showing ~10psi top end but still using the factory solenoid so there might be more mods than that (as factory solenoid is supposedly to be 5->7)

Exhaust looks stock as far as I can tell too.

dyno graph

wow 160 for those mods

very nice

was this on the race pace dyno mupkant? i got 153rwkw as well with safc pod boost but i have an exhaust, mine should probably have more power but i dont mind because im getting cool suspension soon and should be able to turn a lot better :)

was this on the race pace dyno mupkant? i got 153rwkw as well with safc pod boost but i have an exhaust, mine should probably have more power but i dont mind because im getting cool suspension soon and should be able to turn a lot better :)

i have no idea, but originaly they dynoed it with only boost and it was about 142rwkw, then with the tuned safc, they said i got an extra 10 or more rwkw.

Not to mention it was dynoed on friday which was 36 degrees day.

I got 160.6rwkw from AVO with known mods pod, clutch.. though a/m boost guage was showing ~10psi top end but still using the factory solenoid so there might be more mods than that (as factory solenoid is supposedly to be 5->7)

Exhaust looks stock as far as I can tell too.

dyno graph

ive heard plenty about the AVO dyno readings...

Inark, it was on an official WRX club dyno day and everyone else who had their cars dyno'd - majority WRX though, didn't seem to be concerned about the figures (people who have dyno'd else where too).

So since it wasn't just me by myself there'd be no need for them to try and boost the readings.

From what I've heard AVO is supposedly as accurate as Docklands STI's one too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...