Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

  • 4 weeks later...

21-02-2004, 02:45 AM #32

fooey

Registered User

Age: 21

Location: Melbourne I got 160.6rwkw from AVO with known mods pod, clutch.. though a/m boost guage was showing ~10psi top end but still using the factory solenoid so there might be more mods than that (as factory solenoid is supposedly to be 5->7)

Exhaust looks stock as far as I can tell too.

dyno graph

................................................................................

..

man i knew that thing had a set of balls when i had it

160rwks is unreal for a stockish car

worst ever cent of 23,000 when i baught it back in da days

Shit man i cant make it on saturday, realli wanted to go but i gotta go to skool and i also have my Cars Timing Belt change. SHIT!!!! U know how much u got @ wheelz :)? cuz i like to know with a dyno chart of course :D dont trust peoples say :D

i have a 1996 gts-t with

3" cat back(and a 2.5" muffler in it to get past a defect)

jamex in box filter.

otherwise stock

and i got 165rwkw shootout mode about 26 degrees ambient temp.

that was apparently a pretty good figure :D

at unigroup in sydney btw.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...