Jump to content
SAU Community

Recommended Posts

Hey Ppls,

Previously I thought the extra throttle body type device was a traction control thing which shut when wheelspin was evident.

I have since been told that this is actually a Variable Intake Flow thingo which acts to increase airflow speed at low rpm by closing like a normal throttle body, and then opening up at high rpm to give bulk airflow.

Now, PowerFCs are suppose to control all features of the engine management, and I would assume that this is a very important part of the Neo 6 engine.

To those who know, does the R-34 PowerFC allow you to control the activity of this throttle body device........??

I would assume that you could adjust this similar to the way you can with the NVCS.

Having said that though, it might have a link to TPS in order to give the best results depending on a lot of other variables......

Anybody with any experience??

Cheers

BASS OUT

Link to comment
https://www.sau.com.au/forums/topic/34851-r34-neo-straight-6-power-fc-question/
Share on other sites

Are you talking about the bit that sits across the inside of the plenum? it's open at low revs, then closes at high revs...speeds up the flow of air at high RPM. If you disconnect it you'll notice the car runs like a dog from about 3200-5000ish,then picks up in the last bit of the range.

Yep, that's the bit.

Any definent answers??

when I disconnected the plug to it last night, the Engine Warning light came and on the Slip/TCS off light lit up and I took it for a drive.

I didn't really notice a lot of difference but the car was cold and I couldn't really give it a good thrashing.

Guest RedLineGTR

The thing that is in front of the throttle body, is for the Traction Control System :D its what limits your revs when u are wheels spinning from the line, hence if you try to launch with the TCS on then you bog down quite bad. Hope it answers you question.

Guest RedLineGTR

The Power Fc will control everything the same as in other skylines (in one way or another) the Neo engine is tuned for more power (more R&D) over the past models. The TCS Has a Seperate ECU for what it does and u cant change any items of how it behaves with the power fc nor do i know any companys that have Tuned it in one way or another.

Guest RedLineGTR

I hope this is what u mean by your question. When the TCS is activated it is activated and if the car starts to slip highly then it kicks in just like i throttle body, like if you are on the pedal to the floor the TCS can ajust its throttle and limit your revs. If the system is off then the air flows how its meant to without any interuption.

My experience with the traction control is as follows.

Going around slight corners and nailing it, the car will pull lose power and then accelerate once grip is gained again.

But in the wet the car will drop spark and the engine will 'strobe' (for want of a better word) for a second and then accelerate, at which point traction will be lost again, and then it will strobe again.

I think maybe in moderate losses of traction, the blade might close, butin big ones it drops sparky and really pulles the reigns in.

If it only works for traction control, I wonder it there is any merit in using it as a variable intake diameter type device????

What makes you think it "drops sparky"? It just closes the valve completely starving the engine of air and probably cuts the fuel at the same time. If you cut spark it would backfire when you gave it back.

At it's most basic it just cuts power so you can get traction back and if you keep your foot down then it will spin the wheels again, thus restarting the whole process.

Abo Bob.

The sound it makes it identical to the sound that my car makes when misfiring on plugs that haven't been gapped properly.

That's why i made the assumption.

But I have been wrong before!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...