Jump to content
SAU Community

Recommended Posts

Hello mates,

I am planning on buying a CF vented hood to reduce some weight but not sure about it. Is it save to drive in the rain with an opening like that? It looks like the water will just poor down on the belts and alternator. My car is daily driven and i dont have a garage to park it in.

I did a search but couldnt find anything, if anyone can point me in the right direction.

Thanks.

  • Nope 1
Link to comment
https://www.sau.com.au/forums/topic/348707-vented-hood-in-the-rain/
Share on other sites

water also comes up from underneith... and no problems there?

Is that weight saving really going to make your 'street' car any faster... 60km/h is still 60km/h.

You'd be better spending that money of a gym membership and losing weight that way (not saying your a chubsy whubsy... just that people can weigh between 70 to 120kg's)

  • Nope 2

As long as the vents were not directly above the exhaust manifold and intake filters that it shouldn't be too much issue,

There are quite a few manufacturers that include bonnet vents from factory and some of these like the Toyota Celica vent their directly above the turbo and alternator without affecting the vehicles reliability.

if the Bearings on your alternator, power steering, and air-conditioning were subjected to lot of water you may find they would wear quicker but I doubt it's going to be that obvious.

Also watch out for water that gets into the valley where the coils are as the plugs will rust and the moisture will work its way into the boots and cause a missfire, it happened to me.

Thanks everyone for the honest replies, i was just a bit concern and didnt want to ruin my engine which i rebuilt. My plan to reduce weight for this "street" car is for when i'm ready with my new setup i can head up to the drag strips and have some fun there.

And to Mr Barraspalding, thanks for caring about my weight, but i already have a gym membership pass and i go there 4 times a week. Next time if you care so much why not ask first instead of being an ass...

water also comes up from underneith... and no problems there?

Is that weight saving really going to make your 'street' car any faster... 60km/h is still 60km/h.

You'd be better spending that money of a gym membership and losing weight that way (not saying your a chubsy whubsy... just that people can weigh between 70 to 120kg's)

  • Nope 1

I've had 3 different types of vented bonnets the 1st was good had the one vent which was centered over the top of the gap between the radiator and front of the engine. I never had any issues with water with this one.

DSCN0177.jpg">

I then changed to a CF Z-Tune style one and the quality was a bit average and had it fitted to the car for a day or two in the panel shop. After the car was outside and in the rain for a little there was water in the engine bay even with the 'tray' fitted (when i opened the bonnet the water collected in the tray spilt in the engine bay anyways)

I then got the Nismo carbon R Tune one which has the rain channels and no water gets into the bay at all as long as you dont point the hose directly in there. The quality of this is unreal..

IMG_2649.jpg"

This is only my expirence with them and im sure there are others who have never had any dramas with any vented bonnet. But living up here in Mackay the rain can be quite tropical at times coming in thick and fast lol..:D

Cheers

Kingy

  • Like 1

same experience as king.

if you can find one with the venting forward of the valley cover (coil and spark cover) you will be fine.

but if the venting is behind the cover you will get water in there when its raining and the car is stationary, while its moving you

will be fine.

The water falls between the engine and the radiator on this one.

g-force0011.jpg

water falls on front of the cover on this one while the car is stationary.

18072010135_clear.jpg

Edit...both of those are 3rd of the weight of the oem bonnet.

I've had 3 different types of vented bonnets the 1st was good had the one vent which was centered over the top of the gap between the radiator and front of the engine. I never had any issues with water with this one.

DSCN0177.jpg">

I then changed to a CF Z-Tune style one and the quality was a bit average and had it fitted to the car for a day or two in the panel shop. After the car was outside and in the rain for a little there was water in the engine bay even with the 'tray' fitted (when i opened the bonnet the water collected in the tray spilt in the engine bay anyways)

I then got the Nismo carbon R Tune one which has the rain channels and no water gets into the bay at all as long as you dont point the hose directly in there. The quality of this is unreal..

IMG_2649.jpg"

This is only my expirence with them and im sure there are others who have never had any dramas with any vented bonnet. But living up here in Mackay the rain can be quite tropical at times coming in thick and fast lol..:D

Cheers

Kingy

If don't mind me asking, where did you get the z tune style from and how much did the r tune set you back? :D

Thanks!!

they dont make a 33 GT-R one at Nismo

i run the genuine R Tune Nismo Omori bonnet on the 34. It does as stated have rain channels under the bonnet and is Dry Carbon

The best one for the 33 is the design by Top Secret imo, it works alot better, than the copies of the z tune for the "33"

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...