Jump to content
SAU Community

Recommended Posts

Everytime I start my V36 it pops up with a warning message in Japanese.

A friend who can read some tells me it's something about Engine Oil, presumably 'please change it'.

My car came into the country with 10,000kms on the clock and I assume a full oil change was done during compliance. It's done 16,000kms now.

I also know in the menus there is a setting where you can adjust the service intervals and all that.

Does anyone know if this warning appears due to sensors in the car, i.e. it can tell the oil needs changing, or is it something that service guys manually reset during a service (which they neglected to do, fair enough being all in Jap).

Link to comment
https://www.sau.com.au/forums/topic/349488-change-engine-oil-warning-v36/
Share on other sites

A friend who can read some tells me it's something about Engine Oil, presumably 'please change it'.

My car came into the country with 10,000kms on the clock and I assume a full oil change was done during compliance. It's done 16,000kms now.

I hope your compliance workshop actually changed the oil.... Im pretty sure that the one who did my car didint drop the oil

I hope your compliance workshop actually changed the oil.... Im pretty sure that the one who did my car didint drop the oil

Yep I had doubts on whether the compliance shop did change the oil in my V36 as well, so I just changed it since I've done just under 5,000km in it myself in the last 4 months. Figured I'd rather be safe than sorry, got some Mobil 1 5W-30 and changed it myself, along with a new K&N HP-1008 oil filter, all up around $120. At least now I have peace-of-mind.

Would you trust the compliance shop? Do you know them personally? My advice would be to just change it if you're unsure, or just get your mechanic to do it. I would say most compliance shops are genuine and would have done their job properly, but why take the risk? For the sake of $120, I'd rather just change it and not find out the hard way they didn't change it!

  • 1 year later...
  • 1 year later...

Did you guys read the thread....?

it's manually set. you can set it yourself inside one of the menu options. check loz's jap translation sticky

If its like the v35 then it has engine oil, engine oil filter, air filter, and something else I can't remember. It is manually set for xkms.

Using CamDictionary for Android, that error message posted above says "Oil filter - set distance has been reached, press maintanance button"

f**king technology, insane!
My second error reads "Engine oil - set distance has been reached. Press the switch information, maintanance. You can set information you chose"

Guess I'm due for a service!

Edited by awsam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...