Jump to content
SAU Community

MAS Meeting - 2nd March - Girl Promoters/Helping hands


Recommended Posts

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

Yeah I was thinking of camping out to get a seat, haha. Or better yet, bring my own directors chair!

Oh and WTF is with all this post rating sh!t now? Did you know you an "unknow quantity at this point" Ash? Or so the little coloured dot says :D

Oh and check out this new one! :throwup:

Yeah I was thinking of camping out to get a seat, haha. Or better yet, bring my own directors chair!

 

Oh and WTF is with all this post rating sh!t now? Did you know you an "unknow quantity at this point" Ash? Or so the little coloured dot says :D

Yeah, maybe BYO a few seats next week i think :D

And FUG the rating dot. As if i care

Will i be considered a trailtor if my car is on the Ice Performance stand along with leewah GTR, niges supra, bens (racepace) GTR and another few high hp cars?? My hand was twisted into putting my car onto their stand.  smokin.gif

Denham - your car was already designated for the Ice/Fangartists stand. Basically the 2 stands are going to be back to back so there is no issues at all as there are a couple of SAU skylines on the Ice stand + there will be Skylines with Ice stickers on the SAU stand. So its all good.

:D

oh yeah i forgot about that...

yeah its going to be mad.... 40 cars all together with the center being the wini GTR! ooooooooooooooooooooooooo i cant wait!!

Great turn out last night...

Sorry i had to leave early...

Still hard to put faces to forum names... mannnn we need daggy name tags.. lol :D

Will see you next week..

Same time same place???

TTFN

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...