Jump to content
SAU Community

Recommended Posts

Yes to all

well that's hardly comparable.

E85 changes the rules somewhat similar to race grade fuels.

You often can make 30-40rwkw extra with the restriction in place.

You result would be close to 300 when you take 40 off for E85, and then 20 for hubs.

You'd hardly then be running 27psi without the fuel too :P

So was my 3" exhaust @ 270rwkw/17psi when it was showing an issue/restriction. :)

Drop in race fuel (sunoco 104) and all of a sudden we were @ 370rwkw/24psi with the same exhaust. We could use more timing and boost everywhere.

Just goes to show it's not just about the gas :)

Obviously exhaust and manifold are not the same particular part, but similar issue none the less.

I've seen another car with GT-SS's do the same thing PULP vs Race fuel and a 3" exhaust

Thats very very cool, always suspected they should be able to make that kind of power with an un-shy amount of boost - wicked power at 4000rpm too :D

Any plans to get it on a dragstrip or something?

Just on a side note... The AMMRR dyno seems to spit out some very kind figures even for a hub dyno!

"Simon-R32" 3076R 0.63 rear is spitting out what would seem impossible hp for the boost level and "wasnt me" with his internal w/g 3076R 0.8 rear is spitting out huge numbers at low revs that also appear impossible...

I'm not trying to start a shit fight in regards to dyno results but I think they might have to be taken with a grain of salt!

Just on a side note... The AMMRR dyno seems to spit out some very kind figures even for a hub dyno!

"Simon-R32" 3076R 0.63 rear is spitting out what would seem impossible hp for the boost level and "wasnt me" with his internal w/g 3076R 0.8 rear is spitting out huge numbers at low revs that also appear impossible...

I'm not trying to start a shit fight in regards to dyno results but I think they might have to be taken with a grain of salt!

i would agree 100% thats why i said it would make between 350-360 rwkw on a chassis dyno.... ill tell you right now my cars not making 411rwkw lol

i would agree 100% thats why i said it would make between 350-360 rwkw on a chassis dyno.... ill tell you right now my cars not making 411rwkw lol

Yeah fair call... STP correction apparently is the highest correction (so maybe get them to turn it off when they print off the graph). Might even try to put correction on my runs to see what it makes haha

To the defense of the guys in Adelaide it's a bit hard to run a mph when they don't have a drag strip (kehehehe)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...