Jump to content
SAU Community

Recommended Posts

95 25t

1. Twin dump pipe full maundrel bent system 3 inch turbo to tip

2. Turbosmart bleed @ 11 psi

3. K&N panel filter (hehe - 1kw)

Rest of the car stock.

How many kws would I have gained do u think?

Next on my list is hybrid fmic, then PowerFC. Hoping for close to 200rwkw

with all that plus good tuning... :bs!: ?

Link to comment
https://www.sau.com.au/forums/topic/35025-how-much-power-do-i-have-not-much/
Share on other sites

A power run should set you back arpund $40.

Woah! Is that all... Thought it would be at least $100. Anybody know a good dyno on Brisvegas northside?

Be pretty happy with 165rwkw, that would mean 30kw for $1300. Mmmm $1700 for hybrid fmic but i have nfi how much power gain from that maybe 10 rwkw? I've heard of peeps getting 20 rwkw's out of powerfc though, maybe another $1500 + tune. Should be near my goal then for about $3150.

Should I be looking @ stonger clutch before all this or will standard b ok up to 200 rwkws? Woops forgot a whiteline kit too didnt i...

Hey stop newby bashing u :flamer:

not heaps because with those sorts of mods the std ecu runs rich as we all know and have experienced. I reckon around 140 - 150 rwkw depending on dyno.

Your future mods sound good but I think when you get the power fc, thats when you can make the most of the mods u have.

well as a base idea for u. I got a 12/93 r33 gtst. When i dynoed it, it had a cat back 3 inch, pod filter with no air feed, and boost controller set on 13psi and i made 213rwhp(bout 160rwkw) u would be around that mark i would think. Give or take 10 kw

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...