Jump to content
SAU Community

Recommended Posts

what about a full Cometic multi layered steel gasket set.

Full set for intake, exhaust, head etc. Cometic Street Pro - http://cgi.ebay.com/ebaymotors/Cometic-Street-Pro-Top-End-Gasket-Kit-R33-RB25-RB25DET-_W0QQcmdZViewItemQQhashZitem3efbaa0556QQitemZ270510196054QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

no issues then running 18psi, right in the turbo nice-zone :)

same injectors, similar mods, gt3076r IW, chip+piggyback, 250kw@wheels (auto awd)

really an 040 isnt big enough???

mines flowing enough to feed 550cc injectors without a fuel reg or rail pressure bump and Im sure Ive read it can supply larger injectors too.

A fuel pump flows more fuel at a lower fuel pressure. Increasing the fuel pressure above standard will only make the fuel pump run out of flow quicker.

I would put a factory airbox on it with a panel filter.

So you already have the 4bolt dump pipe? That is handy!

Injectors: From my car I can extrapolate that if you want to run 11.5:1 on standard pressure then you'll only get ~250rwkw. If you bump up the pressure a tad and are willing to run to 90% duty then you'll get a bit more, perhaps 280rwkw. So they are borderline, but SHOULD be just enough. They are 450cc btw and allow a lovely idle.

Tune at 1.1bar and be happy - get a hand controller to self adjust the part throttle.

Then buy tyres in bulk.

I would put a factory airbox on it with a panel filter.

So you already have the 4bolt dump pipe? That is handy!

Injectors: From my car I can extrapolate that if you want to run 11.5:1 on standard pressure then you'll only get ~250rwkw. If you bump up the pressure a tad and are willing to run to 90% duty then you'll get a bit more, perhaps 280rwkw. So they are borderline, but SHOULD be just enough. They are 450cc btw and allow a lovely idle.

Tune at 1.1bar and be happy - get a hand controller to self adjust the part throttle.

Then buy tyres in bulk.

I disagree with the factory airbox, you will loose a signifant amount of power. Its criminal on a 3076 imo. If you are certain on keeping the factory airbox then at least upgrade the intake piping to 3" metal. Someone on here had one made up and it was quite expensive as it must join the airbox at exactly the right location.

You will gain power with a 3" metal intake and pod (preferably shielded) when above 250rwkw.

See the quoted post above regarding those small injectors. It is criminal using such small injectors on a 3076 turbo, it will limit you. Otherwise, get a smaller turbo. No point having a large turbo running low boost and relatively low power.

Sell your current injectors and upgrade to larger ones, shouldnt be more than a few hundred changeover and then you will never have to worry about it again. You can then allow your turbo to do its thing, even run E85, or up the boost if you do an engine build one day etc etc. Not to mention it is safer to run injectors less than 80% duty cycle. Sell you fuel pressure regulator and put it towards the injector upgrade instead.

I would have to recommend getting at least 600cc injectors if you want to run pump fuel

and larger again if you wish to run E85 as others above have said and you shouldn't have

any trouble with larger injectors with a good tuner. have a look at deatchwerks in america

for larger injectors especially with the current exchange rate.

Whats your radiator like? A Gtst running 300kw makes a bit of heat esp. on a hot day. I'd get it serviced and cleaned [or new whatever you decide]. I'd even consider an oil cooler kit as well.

And you will want a boost controller, a dual solenoid one is the ducks guts.

But your setup is the basis for a lot of fun............

^^^ not essential at the very minute but top recommendation in future.

I would replace your 'cooler core mate, dont worry about the plenum. Browse the ForSale stuff for a Jap-brand second-hand one.

+1 for PFC hand controller!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...