Jump to content
SAU Community

Recommended Posts

must look at this once I get my launch diagun back.. I do not remember seeing a menu for HVAC in the earlier cars. it IS there for the later ones (V35/V36)

fari point about the undocumneted BUS as well.

$1E - (B7) that is the compressor control relay. output. writing to that will fire the compressor up.

$13 - (B4) AC request input from HVAC unit.

$43,$47 - that is where I would be playing myself.

*looks* like you can get access to it IF the unit supports it.

I'll have a look for the actuation tests once my diagun comes back.

"basically not", are you saying that you can communicate with the AC control unit (at least on your R33 GTS/whatever real model it is), i.e. it exists on the consult bus?

At least for my 33 gtst, a positive definate maybee.

in short, there are active tests for the doors (fresh/recycled air, dash/vent/foot) and fan test with 2 speed etc etc but you can only adjust the cabin temp by +-2 Deg (not enough)

however the mysterious test 0x44, could easly set the temp and more ( the temp range could be covered in 5 bits, leaving 3 spare), I just havn't found any further info on ox44, or had the time to sus it out.

the potential is high to hijack the A/C via Consult, however it does seem to fall in the 'just to easy' category

attatched the file, see last page, last couple of lines

Generic_Nissan_ECU_Sensor_or_Data_register_table_Ver_2.pdf

Bundy

ps piped by slow typing AGAIN !!

Edited by BundyBear

$42 - set temp location. VAL/16 is the word to write to it. that LOOKS like the right spot.

looking further at that I *think that is the cabin temp sensor read location. correct me here.

fond of the unknown myself, but having the standard controls and consult access woult be very nice, best-O-both worlds

yea can't leave God's country but ...hehe

got a bro-inlaw up there but ... another 33

Edited by BundyBear

$42 - set temp location. VAL/16 is the word to write to it. that LOOKS like the right spot.

looking further at that I *think that is the cabin temp sensor read location. correct me here.

I read as:

0x20 0x21 0x22 Temp sensors

0x42 target temp (ie display temp) 0x40 as a trim

then again there's

0x26 sun load, could be a calculated value?

& 29, 2A

Edited by BundyBear

when ive got some time ill try get the consult2 out and sus it out.

if there are any official listing of the names of the data sensors, and active tests, from the service manual (i.e. like how most service manuals have, in the EC section, an on-board diagnostics bit which lists all the data sensors/active tests and what they mean), that'd make things easier to find.

once I get my launch back I'll take a few snaps of the data screen. I usually have a R32,33 handy to fiddle with so it wont be an issue.

I read as:

0x20 0x21 0x22 Temp sensors

0x42 target temp (ie display temp) 0x40 as a trim

then again there's

0x26 sun load, could be a calculated value?

& 29, 2A

$26 - that will affect the $40 value. unsure by how much though.

would be good to have one of these things mocked up on a bench with all the sensors attached. that way you could write to the registers and see what you could and could not access.

What init string are you using, from memory the documented DF ecu does not respond over my consult, I do have something at 0xE7 which afaik is undocumented, always thought this might be the a/c on a 33? Either that or ABS.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hmmm, what do you mean by getting weaker? And where did you get that test done? I've been wondering about my battery because the cold starts crank super slowly. The voltage is fine. Not sure if cranking amps can be checked at home. Battery is 4+ years old.
    • No. The simplest wastegate hookup, with no solenoid or other form of "boost control" (ie, control over your boost control, if you know what I mean) is a single hose, direct from the turbo outlet/hot pipe, straight and only to the wastegate actuator. It is that pressure signal that drives the wastegate to open, providing the boost control (and by "boost control" here, I mean, limiting how high it can go, which is essentially the spring pressure of the actuator). You only end up with tee pieces and alternate flow paths once you start adding things to the boost control system to allow you to determine how much of that boost signal makes it to the actuator. There are so many ways to do that that there is no single way to run the hoses and tees and the like. If you have a stock boost solenoid, then all it does is either allow all the boost signal to go to the actuator, or open up to allow some of it to bleed off. There needs to be a restriction in that bleeder to allow only a small amount to bleed off. And in a stock system, that would then be plumbed back to the turbo inlet (for "emissions control" reasons). That is actually what that nipple on your BOV return pipe could/would be for. If you have an aftermarket boost controller and solenoid, then the above is mostly true, but there is no need for a restrictor in the bleed, because the solenoid is pulse width modulated to create a variable bleed off. The air that escapes from the bleed can either be vented, or also returned to the turbo inlet. For emissions reasons it should be returned to inlet, but the amount of air being vented is so small that it really doesn't matter (either from an emissions perspective, or from an air-fuel ratio affecting perspective).
    • And other times you just need to go buy bigger injectors?
    • Yup. I actually just blew my turbo. LOL.  should have checked this thread before today. i also have no boost solenoid. so it should be...one line from wastegate to turbo inlet, and a T somewhere in that line that connects to the wastegate return pipe?
    • It's recommended, however I can assure you a good amount of people don't bother. FWIW, the OEM battery lasted 4.5 years and I changed it prematurely too, I reckon could have stretched it to 5 years.
×
×
  • Create New...