Jump to content
SAU Community

Recommended Posts

Hey guys wondering who could help me out running at idle only has 30psi fuel pressure at idle, and only goes upto around 35psi engine off

Has walbro fuel pump running on full 12v from battery

new fuel filter

stock injectors

stock regulator

using a turbosmart fuel guage setup on the line from the filter to the back off the injector rail

R33 gtst rb25det

thanx any help would be great !

Link to comment
https://www.sau.com.au/forums/topic/352837-low-fuel-pressure/
Share on other sites

I think the filter would be on the intake side before the injectors, well thats where i put mine on both our cars, but just check that all the lines are on in the correct order it should go from the fuel pump to filter, then to fuel rail, out of the rail into the fuel regulator, then back to tank. Maybe this could be a problem if the fuel regulator is hooked up back to front.

You need to check fuel rail pressure with the air/boost signal hose disconnected and blocked

Fuel rail pressure is around 2.5bar at zero manifold vacuum. That's about 37-40psi.

If you haven't removed the air/boost signal to the fuel reg, at idle it may be pulling around 20" vacuum or the equivalent of around 10psi.

So with the signal hose connected, you'd only see a fuel pressure of around 27-30 psi.

I think the filter would be on the intake side before the injectors, well thats where i put mine on both our cars, but just check that all the lines are on in the correct order it should go from the fuel pump to filter, then to fuel rail, out of the rail into the fuel regulator, then back to tank. Maybe this could be a problem if the fuel regulator is hooked up back to front.

the incoming fuel is going through the filter into the rail then out the reg to the fuel damp back to the tank thats right isnt it?

You need to check fuel rail pressure with the air/boost signal hose disconnected and blocked

Fuel rail pressure is around 2.5bar at zero manifold vacuum. That's about 37-40psi.

If you haven't removed the air/boost signal to the fuel reg, at idle it may be pulling around 20" vacuum or the equivalent of around 10psi.

So with the signal hose connected, you'd only see a fuel pressure of around 27-30 psi.

disconnected the air hose to the reg and blocked the feed, it went from 29 to 35 psi.

also could try and pinch the fuel return line and if rail pressure increases, then your fpr is stuffed. fuel filter is on the intake line. no good filtering fuel thats already gone through the system

i pinched the return line from the reg and the fuel pressure was rising all the way upto 60 psi if i left it there does this mean my reg is gone?

Low fuel pressure, it is difficult to run the country. If you are worried about the pressure on oil prices, the installation of a Mei Ling M55A is a pump with a high volume pump std spring. When all fails, do a fuel pressure, fuel quantity test, could save you from chasing your tail and throwing good money at the wrong problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...