Jump to content
SAU Community

Recommended Posts

Greeting guys,

Newbie here. My car's a 1993 R33 Gts25t with mods:

Blitz pod with CAI + heat shield, FMIC hks gt 600x300x100mm, cat converter removed with 3 inch exhaust, hks sqv bov.

My car's done 90k, serviced every 5k (I used 100% synthetic - Mobil1)

1. Will I get 200rwkw when I install emanage and Profec e-01 boost controller (and get it properly tuned!)?

2. How does 200rwkw translate to BHP??

Cheers guys, awesome bunch! :headspin:

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Hmmm...

I think the man you need to talk to is Ben Martin :D

200rwkW is possible on the stock turbo but it's a freak thing where a good engine + a whole bunch of cheap mods (ie, dumps, EBC, FMIC) may get you there.

I would bargain on a lot more mods to get 200 RELIABLY day in day out like a good turbo like the HKS 2530.

The ECU is reasonably irrelevant, it may get you a few kW but it comes into it's own with you get up into the 225+ class.

200rwkW means something like 250 crank kW so it's a fair lot.

Something like 268rwhp.

T.

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705332
Share on other sites

Thanks, I just want my skyline to be capable of 200rwkw but I dont need that sort of power everyday (too much traffic here in KL :D ).

From what I read in the threads, fuel controller adds a fair bit of power (around 10-20rwkw) on its own, and should make some more with an EBC.

so 200rwkw is about 330-340 BHP. Quite happy with that! Hehe, until the next round of mods

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705397
Share on other sites

200 is not a huge ask. I had it with just power fc, fmic, full exhaust (but be aware, a not all 3" exhausts are equal), pod with partition and CAI and boost. This was at 0.85 bar, which I ran all day every day without a problem. At 1 bar, I think you would be closer to 210 or so, which is also realistically obtainable with stock turbo.

It will be very worthwhile to upgrade your fuel pump too, as a bit of insurance against detonation. Your afm may be out of resolution here too. Not a major problem if you will be running only one boost pressure for top end, but it can offer gains by upgrading. If you plan on upgrading your AFM, it is worth doing it before you fit the e-manage, it will save you a few dollars in tuning costs.

But definately get your fuel pump upgraded before you start more serious tuning.

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705446
Share on other sites

Guest INASNT
My brother got 198rwkw from his 33 with just:

FMIC

Full Exhaust

Bosch Fuel Pump

K&N Pod (no CAI or heat shield)

Boost set to 12psi

Final Tune

This was at Advanced in brisbane, with standard computer and standard turbo.  So it is possible with simple bolt on parts.

so what did they actually tune since u got a stock ecu???

Any place can bodge dyno figures to read whatever u want.

gobiz

if u get z32 afn u will need new management otherwise the car will run like crap

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705764
Share on other sites

INASNT, he is fitting e-manage.

gobiz, the boost pressure isnt the problem, its the airflow, as the AFM measures how much air is being sucked in. I know sydneykid hasnt had a problem at 200kw with the stock AFM, but mine hit 5.1V (max) at around 4500rpm with only 189rwkw. I know I am not the only one this has happened to. As mentioned, it wont make a big difference if you are tuning to one boost pressure, but if you want to tune to 1 bar, and be able to turn the boost down, the ECU may not see the change in airflow, thus overfueling.

If you are after a GTR pump, can I suggest a post in the Wanted to buy section, or try contacting www.d1garage.com or www.japanesemotorsport.com.au as they get these in quite often.

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705774
Share on other sites

THANKS Steve,

I'll try looking for the Z32 AFM round the wreckers here in KL. I'll try to get the fuel pump as well.

*Sigh* just thought I had enough money saved for the mods......now gotta save up more

;)

That always seems to be the case with modding, last time i put the FMIC in, I had to get a whole new front bumper plus get it painted plus get new signal lights.

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705813
Share on other sites

so what did they actually tune since u got a stock ecu???

Any place can bodge dyno figures to read whatever u want.  

gobiz

if u get z32 afn u will need new management otherwise the car will run like crap

sorry, I meant tune as, new plugs, check timing, air fuel ratio, compression test, etc.

yes true i have seen a few places bodge dyno figures but advanced in brisbane is a very respected and well known workshop. depending on the day and the dyno, figures can be different.

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705828
Share on other sites

gobiz, AFAIK there is only one Z32 AFM, 80mm (same as RB25) but has an orange sticker on it. If you are getting it from a wrecker, try and get the plug too, as they are different from a RB25.

If you dont have the $$, its not a huge thing at this sort of power level. Just tune the car up with stock AFM at around 0.85 bar you should have no problems with reliability at that sort of boost, and can drive around all day every day at the same boost.

Alot more important you upgrade the fuel pump - think of it as insurance.

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705853
Share on other sites

Steve, is the emange very similar to a unichip. they both maintain the standard ecu, and they are both interceptor. they both control fuel and ign.

what im gettin at is that when i get my car tuned for 1 bar on wednesday, if my afm is running out of resolution, will the car still go alrite considering im gettin it tuned at 1 set boost level.

thanks

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-705964
Share on other sites

Maybe, hard to say until the final tune is done. Can you check the AFM voltage when you do the unichip?

It would be worth getting them to tune it and do a run at lower boost (without changing the tune) and see what happens to the AF ratios. If she starts running rich you may have your answer.

Have you done your fuel pump yet dean?

Link to comment
https://www.sau.com.au/forums/topic/35306-can-i-get-200rwkw/#findComment-706024
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...