Jump to content
SAU Community

Recommended Posts

Okay I have a vipec plug-in ecu. Now when it was tuned it turns out that the aircon wasn't working. The compressor itself wasn't activating. Now I have since had that fixed, it was a problem with the climate control unit, and I have had an extra switch put in to activate it.

Now the problem is whenever the aircon is activated the car has a tendency to stall when stopping, it appears that the ecu doesn't increase the revs in time to prevent the stall. It normally doesn't do this when the aircon is off. I presume this is due to less load on the engine. What would be the best way to fix this? Increase the idle speed? As it also tends to idle a bit low when the aircon is on.

Link to comment
https://www.sau.com.au/forums/topic/353082-vipec-idle-issue/
Share on other sites

In the ECU software increase the values in this table a bit and it should increase the revs when the aircon is on.

Idle Speed Control > Idle-Up Tables > Aircon Step

You could also check the RPM lockout value (mine is set at 400, however i have never had aircon so dont know if this is high enough with it on)

Idle Speed Control > Idle Speed Control > RPM Lockout

In the ECU software increase the values in this table a bit and it should increase the revs when the aircon is on.

Idle Speed Control > Idle-Up Tables > Aircon Step

You could also check the RPM lockout value (mine is set at 400, however i have never had aircon so dont know if this is high enough with it on)

Idle Speed Control > Idle Speed Control > RPM Lockout

RPM Lockout is at 800rpm

change my Aircon step from 5.1 to 8.1 across the the board. Will see if this makes a difference. It did seem to help the idle of the car when I had the car connected.

Ever since I got my AC working on the Vipec the idle wasn't perfect with it on, so I played around with it a bit and it was good enough (not perfect) so I left it like that.

However I was just thinking, is the AAC actually set up on the base map?! I don't remember ever seeing it on the Aux output?

EDIT: I just loaded up VTS and noticed it is in its own folder called Idle Speed Control. However what output is that actually using?

I have the same issue, really low idle when aircon is on with vipec plug in. mine is in need of a retune once i get new turbos etc so il get it fixed then, but i never had aircon regassed when ecu was installed either so now i know im not the only one with the problem lol

for a list of all analog/digital outputs and inputs and what they control, get the gtst/gtr manual off the vipec website.

the help file is ACTUALLY helpful. its by far the most comprehensive guide ive read. any issue ive had with my vipec ive searched the help file and its explained it all there in great detail, and it gives you a good idea on how it works.

Yeah the help file is great, I use it all the time. Makes it so much easier.

I got it to idle with the aircon on without stalling now which is great, however it still hunts up and down from 800-900 a bit. Not really sure how to smooth that out. Will keep trying.

Ahh good thinking. Yeah it is closed loop and the deadband is set to 30rpm. I'll try setting it to 100rpm or something and see how that goes.

So many thing to adjust!! Haha.

If you want it to idle properly you need proportional spark as well as closed loop idle control. The trick is to find the advance at which +/-10 degrees of timing gives you an equal increase/drop in rpm then apply your delta igntion numbers corresponding to the rpm you found and make your base idle timing the number you found earlier. Make sure you turn off all IAC control while doing this though.

Open up the bounds on the idle control to at least 100-150rpm you want it to do very little until +/-200 rpm from you desired idle speed..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...