Jump to content
SAU Community

Recommended Posts

Hey guys and girls, I currently have a rb25 that has been rebuilt from the ground up less then 1 year ago , the engine could possibly have around 15,000 on it now .

The issue I'm having is blue smoke out the exhaust ONLY when the car has been sitting at idle hot or cold for a period of 5 minutes or more . After a big rev it won't come back till it sits another 5 minutes or so . When driving the car I cannot see anything and my friend said he can't see smoke while I'm driving / thrashing it when he follows .

Engine currently makes 300rwkw on 18 psi and drives / runs smooth ? Should I be worried and what can cause this issue ? It's in no way blow by because my catch can setup is correct and has no traces of oil at all !

Some help with this situation would come in handy so I can stop chocking everyone out lol . Also forgot to say the car has not chewed any oil since service 2 weeks ago and oil is still gold .

Link to comment
https://www.sau.com.au/forums/topic/353144-blue-smoke-after-idle/
Share on other sites

did it do it as soon as you installed the turbo?

do they require different oil restrictors for the GTX35?

take the dump pipe off and have a good look around the turbine

The GTX35's come with a restrictor on the core suitable for themselves dont they?

if GCG's over the phone, uninformed investigation says it cant be the turbo, then it must be the turbo /sarcasm. if you arent getting blow by and if your intercooler piping isnt full of oil then my guess is its the turbo. oil could be pushing past the ring that is meant to seal it (not sure what its called).

check the turbo if not turbo must be valve stem seals. i used to be an engine rebuilder and we had this problem often. even they are new stem seals and they were not installd correctly such as burrs on the valve stems when installing them knicking the the seals. but def sounds like sem seals with the symptoms you are telling us. if it was turbo related id say it would pretty much constanly blow smoke.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...