Jump to content
SAU Community

Recommended Posts

ok let me first say, that this is typically what happens to me

i changed my spark plugs today, with BCPRE ones, and i used to have BK.. somethings... and the new ones are longer by a few mm, i dont know why its relevant but id like to say every detail

i changed them over no dramas, turned the car on and i have what seems to be a lifter ticking, and i have no idea why its doing this now....

i know this is a near impossible question, but any ideas WHY?!

ok let me first say, that this is typically what happens to me

i changed my spark plugs today, with BCPRE ones, and i used to have BK.. somethings... and the new ones are longer by a few mm, i dont know why its relevant but id like to say every detail

i changed them over no dramas, turned the car on and i have what seems to be a lifter ticking, and i have no idea why its doing this now....

i know this is a near impossible question, but any ideas WHY?!

Spark plugs are most likely wrong, the contacts aren't firing properly.

change the plugs again trial & error, it may even be that the plugs aren't

positioned correctly your engine's probably running on 5 cylinders...

Spark plugs are most likely wrong, the contacts aren't firing properly.

change the plugs again trial & error, it may even be that the plugs aren't

positioned correctly your engine's probably running on 5 cylinders...

engine runs smoothly, exact same as before, i put the old plugs back in straight after, and was still ticking.

when you change your plugs, it's a good idea to use a compressor or a vaccum to blow/suck out the dirt in the valley before you pull each plug out, so dirt and crap doesnt fall into the cylinder.

anyway, i doubt that would cause ticking, unless it was a big chunky piece of something that fell in.

i changed my spark plugs today, with BCPRE ones, and i used to have BK.. somethings... and the new ones are longer by a few mm, i dont know why its relevant but id like to say every detail

The fact that nobody has commented on that worries me.

I know on SR's there are issues with particular spark plugs being slightly too long, and will hit things internally... I wouldn't be surprised if this is the case on RB's too.

Have you considered swapping your old plugs back in and seeing if the noise goes away? If it does, you've pretty much isolated the noise to those spark plugs.

He said he did try the old ones again, and the ticking was still there, but now has gone away.

Could it be possible that you simply left the car sitting, off, for a decent amount of time such that a decent amount of oil had drained to the bottom, causing noisy lifters?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...