Jump to content
SAU Community

Recommended Posts

for sale:

r32 front stock discs - $10

r32 front slotted discs - $10

r32 grey rear wing - $5

stagea front & rear stock swaybars - $20

stagea front stock camber arms - $20

throwing the r32 stuff away mid-week if not taken..............

R33 Series 2 Frontbar....no fog lights $200

R33 series 2 Rear bar.... melted a bit round the exhuast...$50

RB20DET Silvertop... selling as a parts motor as i dont know if it runs... comes with Flywheel..$300

Pick up in Gawler/Craigmore

post-43023-0-31102200-1297572811_thumb.jpg post-43023-0-96283300-1297572822_thumb.jpg

Edited by WLD MAN

mind u i do know how ppl can make the mistake,

when u go in the FS section, people must hit the start new thread instead of add reply!

and the thread get made in the general section not the sticky!

I have the complete (dumps, front pipes, hollowed cat, cat back) stock exhaust system off my old R33 GTR which i no longer own.

I need to get rid of it to clear some room in the shed.

I also have a walbro fuel pump that was used for about a day.

Fuel Pump: $75

R33 GTR Exhaust System: $600 ono

Willing to post pump but exhaust will have to be picked up by the buyer or i can arrange drop off in the Adelaide Metro Area

AWESOME TRACK CAR

1992 r32 4door

IMPORTED THREW ADELAIDE JAP NOT QUIT 2 YEARS AGO

-120,000 klms

-custom fresh turbo from ATS ( using r34 op6 )

-greedy fmic,mostly truck clamps

-Earls oil cooler an relocator

-dose pipe, afm relocated

-am screamer

-strate pipe with 1 ressy SOUNDS TUFF

-power fc an controller

-hks evc5

-adjustable cam gears inlet an ex

-walbro pump

-heavy duty extreme clutch (do have brand new 6puck waiting go in)

-brand new headgasket, belts and lines

SUSPENSION

-npg coils in front

-isc in rear

-whiteline front adj sway,extra bracing

-whiteline rear adj sway, extra bracing

-GTR strut brace front

-strut brace rear

-brake stopper

-33 lcas

-hicas lock

-kkr camber

-kkr castor

INTERIOR

-kenwood mp3

-kenwood speaker fr an rear

-greddy indiglo boost gauge

-shift light

_FREEZING COLD AIR_

EXTERIOR

-weathershields

-custom side skirts

-pods

-custom front bar

-roof wing

( has drift scar from white refector passenger rear quarter)quoted $800 to metal finish an paint !

- an custom dents above each pumped guard

-will come with 33 stockys

DEFECTED FOR TRACK AND REAR TOO LOW, 18+22/10'S ALL ROUND track was out by 10mm and rear too low by 20mm

MAKE AN AWESOME TRACK WHORE :P

$7000 firm or less with parts removed !

32 GTR DIFF IN CRADLE WITH DRIVE SHAFTS, HICAS AND SOME ARMS $200 THE LOT.

32 GTR FRONT (ALLOY) GUARDS ONE HAS SMALL DING $150....WITH GTR INDICATORS $180

32 GTR FRONT BRAKES $200 O.N.O

32 GTR FUEL PUMP IN CRADLE $70

I ALSO HAVE 32 GTR RADIATOR SUPPORT CUT AT THE STRUT TOWERS ...OFFER?

TEXT 0415 23 23 97 IN S.A WESTERN SUBURBS.

pics here http://nissansilvia.com/forums/index.php?showtopic=478704

2X AM Performance blast pipes, like new, to suit any car, if your baller enough! $240 each. can fit for extra.

180333_1756435224060_1034359196_1934509_1459083_n.jpg

hey mate, what size are those blast pipes you have for sale? are they baffled or straight thru?

Any ideas on how much to get them fitted to my stagea, 3 inch inlet

cheers,

robbie

2X AM Performance blast pipes, like new, to suit any car, if your baller enough! $240 each. can fit for extra.

180333_1756435224060_1034359196_1934509_1459083_n.jpg

Hey mate, can't tell by the photo, are they sliced or cut evenly?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...