Jump to content
SAU Community

Recommended Posts

for sale:

r32 front stock discs - $10

r32 front slotted discs - $10

r32 grey rear wing - $5

stagea front & rear stock swaybars - $20

stagea front stock camber arms - $20

throwing the r32 stuff away mid-week if not taken..............

R33 Series 2 Frontbar....no fog lights $200

R33 series 2 Rear bar.... melted a bit round the exhuast...$50

RB20DET Silvertop... selling as a parts motor as i dont know if it runs... comes with Flywheel..$300

Pick up in Gawler/Craigmore

post-43023-0-31102200-1297572811_thumb.jpg post-43023-0-96283300-1297572822_thumb.jpg

Edited by WLD MAN

mind u i do know how ppl can make the mistake,

when u go in the FS section, people must hit the start new thread instead of add reply!

and the thread get made in the general section not the sticky!

I have the complete (dumps, front pipes, hollowed cat, cat back) stock exhaust system off my old R33 GTR which i no longer own.

I need to get rid of it to clear some room in the shed.

I also have a walbro fuel pump that was used for about a day.

Fuel Pump: $75

R33 GTR Exhaust System: $600 ono

Willing to post pump but exhaust will have to be picked up by the buyer or i can arrange drop off in the Adelaide Metro Area

AWESOME TRACK CAR

1992 r32 4door

IMPORTED THREW ADELAIDE JAP NOT QUIT 2 YEARS AGO

-120,000 klms

-custom fresh turbo from ATS ( using r34 op6 )

-greedy fmic,mostly truck clamps

-Earls oil cooler an relocator

-dose pipe, afm relocated

-am screamer

-strate pipe with 1 ressy SOUNDS TUFF

-power fc an controller

-hks evc5

-adjustable cam gears inlet an ex

-walbro pump

-heavy duty extreme clutch (do have brand new 6puck waiting go in)

-brand new headgasket, belts and lines

SUSPENSION

-npg coils in front

-isc in rear

-whiteline front adj sway,extra bracing

-whiteline rear adj sway, extra bracing

-GTR strut brace front

-strut brace rear

-brake stopper

-33 lcas

-hicas lock

-kkr camber

-kkr castor

INTERIOR

-kenwood mp3

-kenwood speaker fr an rear

-greddy indiglo boost gauge

-shift light

_FREEZING COLD AIR_

EXTERIOR

-weathershields

-custom side skirts

-pods

-custom front bar

-roof wing

( has drift scar from white refector passenger rear quarter)quoted $800 to metal finish an paint !

- an custom dents above each pumped guard

-will come with 33 stockys

DEFECTED FOR TRACK AND REAR TOO LOW, 18+22/10'S ALL ROUND track was out by 10mm and rear too low by 20mm

MAKE AN AWESOME TRACK WHORE :P

$7000 firm or less with parts removed !

32 GTR DIFF IN CRADLE WITH DRIVE SHAFTS, HICAS AND SOME ARMS $200 THE LOT.

32 GTR FRONT (ALLOY) GUARDS ONE HAS SMALL DING $150....WITH GTR INDICATORS $180

32 GTR FRONT BRAKES $200 O.N.O

32 GTR FUEL PUMP IN CRADLE $70

I ALSO HAVE 32 GTR RADIATOR SUPPORT CUT AT THE STRUT TOWERS ...OFFER?

TEXT 0415 23 23 97 IN S.A WESTERN SUBURBS.

pics here http://nissansilvia.com/forums/index.php?showtopic=478704

2X AM Performance blast pipes, like new, to suit any car, if your baller enough! $240 each. can fit for extra.

180333_1756435224060_1034359196_1934509_1459083_n.jpg

hey mate, what size are those blast pipes you have for sale? are they baffled or straight thru?

Any ideas on how much to get them fitted to my stagea, 3 inch inlet

cheers,

robbie

2X AM Performance blast pipes, like new, to suit any car, if your baller enough! $240 each. can fit for extra.

180333_1756435224060_1034359196_1934509_1459083_n.jpg

Hey mate, can't tell by the photo, are they sliced or cut evenly?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...