Jump to content
SAU Community

Thinking This May Be A "super Hicas" Issue

Weapon
 Share

Recommended Posts

Weapon Mentor

Weapon

Posted
Posted

Chasing an extremely annoying issue with my Series 3 R33 GTR. The car has done thise for a while now to be honest but is starting to get a little worse now.

At speeds exceeding 80kp/h it starts to "shimmy" from time to time like the HICAS is making sterring inputs.

Its really bad with more tyre wear and also on less than an 1/8th tank of fuel. I am toying with the idea of getting a HICAS lock bar with the replacement tie rod ends etc but just wanted to get some opinions before i make a move on anything really. I haven't been able to sight anything visually that is wrong with the bushes or mounts etc that would cause anything to "shift"

Any thoughts or ideas woould be greaty appreciated.

Cheers Marty

jrm Veteran

jrm

Posted
Posted

If your HICAS is non-functional or has excessive play in the rear steering rack - it can definitely 'shimmy' at high speed - been there, and experienced it myself. I ended up replacing my HICAS rack, though - for pure street use, when it's working right - I kinda like it (removing/locking it would also be illegal without engineering in SA..)

blk94r33 Mentor

blk94r33

Posted
Posted

If your HICAS is non-functional or has excessive play in the rear steering rack - it can definitely 'shimmy' at high speed - been there, and experienced it myself. I ended up replacing my HICAS rack, though - for pure street use, when it's working right - I kinda like it (removing/locking it would also be illegal without engineering in SA..)

Not something simple such as a wheel im-balance and worn rack-end/tie rod end? But if it's only above the 80kph mark... unsure.gif

jrm Veteran

jrm

Posted
Posted

Not something simple such as a wheel im-balance and worn rack-end/tie rod end? But if it's only above the 80kph mark... unsure.gif

For me it was movement in the rack itself. It could probably have been repaired, but it was easier/cheaper to replace the rack.

For the OP, I suspect it's best he take the car to a quality tyre/wheel/suspension workshop. They should be able to sus things out pretty quickly and figure out if it's the HICAS rack, simple worn bushes or what.

Weapon Mentor

Weapon

Posted
  • Author
Posted

Yea i was thinking it was that, i have been sussing out the kit that replaces the whole rack and tie rod ends etc its about $100 more than just a normal lock bar so i think thats worth it. Its been in two suspnsion joints here in Townsville and they say nah mate she is all good lol so i don't really like taking it to "professionals"if i can avoid it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...